Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Electrical Properties
- Processing Information (Extrusion)
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
- ³ Extrusion parameters are only mentioned as general guidelines.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹ | 66.8 | MPa | ASTM D638 |
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹ | 4.2 | % | ASTM D638 |
Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 10.8 | % | ASTM D638 |
Tensile Modulus (at 5 mm/min) ¹¹ | 2491 | MPa | ASTM D638 |
Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 108 | MPa | ASTM D790 |
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 2600 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Density ¹¹ | 1.1 | g/cm³ | ISO 1183 |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.04 | % | ISO 62-1 |
Melt Flow Rate (at 300°C, 5.0 kgf) ¹¹ | 11.7 | g/10 min | ASTM D1238 |
Mold Shrinkage (flow) ¹¹ | 0.73 | % | SABIC method |
Mold Shrinkage (xflow) ¹¹ | 0.79 | % | SABIC method |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 150 | °C | ASTM D648 |
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 133 | °C | ASTM D648 |
Vicat Softening Temperature (Rate A/50) ¹¹ | 166 | °C | ASTM D1525 |
Vicat Softening Temperature (Rate B/50) ¹¹ | 155 | °C | ASTM D1525 |
Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
Ball Pressure Test (approximate maximum) ¹¹ | 140 | °C | IEC 60695-10-2 |
Value | Units | Test Method / Conditions | |
Surface Resistivity ¹¹ | 7.50E+16 | Ω | ASTM D257 |
Volume Resistivity ¹¹ | 6.20E+15 | Ω.cm | ASTM D257 |
Comparative Tracking Index (UL, PLC) ᵖ ¹¹ | 0 | PLC Code | UL 746A |
Value | Units | Test Method / Conditions | |
Drying Temperature ³ | 1.10E+02 | °C | — |
Drying Time ³ | 3 - 4 | Hrs | — |
Barrel - Zone 1 Temperature ³ | 210 | °C | — |
Barrel - Zone 2 Temperature ³ | 275 | °C | — |
Barrel - Zone 3 Temperature ³ | 280 | °C | — |
Barrel - Zone 4 Temperature ³ | 280 | °C | — |
Die Temperature ³ | 285 | °C | — |
Roll Stack Temperature - Bottom ³ | 20 - 30 | °C | — |
Roll Stack Temperature - Middle ³ | 120 - 130 | °C | — |
Roll Stack Temperature - Top ³ | 120 - 140 | °C | — |
Value | Units | Test Method / Conditions | |
Izod Impact (Notched, at 23°C) ¹¹ | 211 | J/m | ASTM D256 |
Izod Impact (Notched, at -40°C) ¹¹ | 84 | J/m | ASTM D256 |
Izod Impact (Unnotched, at 23°C) ¹¹ | No break | J/m | ASTM D4812 |
Izod Impact (Unnotched, at -40°C) ¹¹ | 1830 | J/m | ASTM D4812 |
Value | Units | Test Method / Conditions | |
Drying Temperature ⁷ | 100 - 120 | °C | — |
Drying Time ⁷ | 3 - 5 | Hrs | — |
Melt Temperature ⁷ | 280 - 330 | °C | — |
Nozzle Temperature ⁷ | 250 - 330 | °C | — |
Front - Zone 3 Temperature ⁷ | 280 - 330 | °C | — |
Middle - Zone 2 Temperature ⁷ | 280 - 330 | °C | — |
Rear - Zone 1 Temperature ⁷ | 280 - 330 | °C | — |
Mold Temperature ⁷ | 70 - 120 | °C | — |
Back Pressure ⁷ | 0.3 - 0.8 | MPa | — |
Screw Speed ⁷ | 20 - 100 | rpm | — |
Value | Units | Test Method / Conditions | |
UL Recognized (94V-0 Flame Class Rating) ʳ | min. 0.25 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Regional Availability