Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Characteristics
- Permanent color
- UV resistant
- Stays fully elastic after curing
- Very good adhesion on many materials
- Very easy application
- Typical acetic smell
Applications & Uses
- Applications
- Application Method
- Cure Method
- Applications
- Building and construction joints
- Glazing on aluminum frames
- Sealing cold storage rooms and containers
- Sealing in air conditioning systems
- Window and door joints
- Methodology
Surfaces:
- Type: all usual building surfaces
- State of surface: clean, dry, free of dust and grease
We recommend a preliminary compatibility test, especially on PVD and powder coated materials.
Joint Size
Minimum width 1/4” Maximum width 1 3/16” Minimum Depth 1/5” Recommendation 2 x depth = width Application:
- Method: Manual or pneumatic caulking gun
- Conditions: 40° F to 95° F
- Finish: soapy water before skinning
- Repair With: Soudasil RTV1
- Clean Up: white mineral spirit immediately after use
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Application Temperature Range | -35 to +140 | °F | — |
| Artificial Weathering | No Cracking | — | ASTM C 793 |
| Curing System | Moisture Cure | — | — |
| Curing Time (1/8” Diameter Bead, 75ºF & 50 relative humidity) | 24.0 | hrs | — |
| Elongation | 500.0 | — | ASTM D 412 |
| Hardness (+/- 5) | 30.0 | Shore A | ASTM C 661 |
| Movement Capability | (+/- ) 25 | minutes | ASTM C 719 |
| Sag (Vertical Displ.120ºF) | No sag | — | ASTM C 639 |
| Service Temperature Range | -40 to +400 | °F | — |
| Skin Formation (75ºF, 50 Relative Humidity) | 5.0 - 10.0 | minutes | — |
| Stain And Color Change | Passes | — | ASTM C 510 mortar |
| Tack-Free Time | 44854.0 | minutes | ASTM C 679 |
| Tensile Yield | 350.0 | psi | ASTM D 412 |
| VOC | 30.0 | g/L | — |
Regulatory & Compliance
- Certifications & Compliance
- Meets
ASTM C 920, Type S, Grade NS, Class 25, Use NT, A, G and O, Federal Specification TT-S- 00230C.
See recommended substrates. FDA/USDA requirements for use in establishments operating under Federal Meat and Poultry Inspection Program. When cured and washed, ingredients remaining or which could migrate to food are listed on FDA Regulation No. 21 CFR 177.2600 NSF Standard 51
- Limited Warranty
SOUDAL warrants product to be of good quality and will replace or, at our election, refund the purchase price of any products proved to be defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, SOUDAL MAKES NO WARRANTY OR GUARANTEE, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and SOUDAL shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith.
Safety & Health
- Health and Safety Recommendation
DIRECT CONTACT OF UNCURED SEALANT IRRITATES EYES AND MAY IRRITATE SKIN. OVEREXPOSURE TO VAPOR MAY IRRITATE EYES, NOSE AND THROAT. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact. On Contact, uncured sealant could cause irritation to skin and eyes. In case of eye contact, flush eyes with warm water for 15 minutes, call a physician. For skin contact, remove sealant with a paper towel. If swallowed, do not induce vomiting, call a physician. Soudasil RTV1 is manufactured for professional use only.
Packaging & Availability
- Packaging Type
- Packaging
10.1 fl. oz. cartridges
Storage & Handling
- Shelf Life
- 12 months in unopened packaging in a cool and dry storage place at temperatures between +41° F and +77° F.
- Storage in excessive heat and/or high humidity conditions may reduce shelf life up to 30
Remarks:
- Not recommended for use on PC and PMMA because it can cause crazing (stress cracking) in these materials.
- Due to acetic character some metals (copper, lead) can be attacked.
- Contact between this sealant and the primary sealants of double glazed insulation windows or the PVB film of security glass should be avoided.
- Do not use as structural glazing adhesive.
- Contact with plasticizer containing plastics (e.g.flexible PVC, butyl rubber, EPDM,…) can lead to incompatibilities, such as discoloration or loss of adhesion. We recommend a preliminary compatibility test.