Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- ColorTec 600WB generates the premier balance of strength, flexibility, and chemical resistance, all in a low odor, low VOC formulation.
- Unlike nearly all epoxies, ColorTec 600WB has remarkable properties related to moisture:
- Withstands high vapor transmission rate, up to 13 pounds per 1,000 ft² (5.4 kg per 100m²) in 24 hours.
- Provides a non-permeable vapor barrier, even in basements.
- Applies on fresh concrete as soon as three days after pouring and placing concrete.
Applications & Uses
- Applications
- Compatible Substrates & Surfaces
- Uses
Applications range from manufacturing facilities, warehouses, bars, clubs, retail stores, automotive showrooms, hospitals, medical centers, residential interiors, garage floors, gyms, locker rooms, stadiums, or anywhere that an exceedingly resilient floor is desired.
- Coverage
- Varies due to porosity of substrate
- As 1st coat approximately 125 - 175 ft² per gal.; 9 - 13 mils wet; 4.7 - 6.8 mils cured
- For smooth surface or second coat approximately 200 - 250 ft² per gal.; 6.4 - 8 mils wet; 3.3 - 4 mils cured
- Application Temperature
50 - 95 °F
- Suitability Sample
- Due to condition specific sites, always prepare an adequate number of test areas.
- Wear protection system and esthetic suitability for products’ intended use should be included.
- On-site sample approval is especially critical on substantial, heavy traffic situation or custom coloration.
- Clean-Up
Before the product dries; spills and tools can be cleaned up with a solvent such as xylene or acetone.
- Limitations
- For use by trained professionals that have read the complete SDS.
- The product is strictly for interior use, upon a well-drained concrete slab with an appropriate vapor barrier, subject to no hydrostatic pressure.
- When masking use caution while taping to a floor that is not completely cured, especially at the edges, as delamination may occur.
- Protect from metal wheel traffic and some furniture where point of contact may be damaging.
- Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking
Properties
- Color
- Appearance
- Gloss Sheen (Cured)
- Odor
- Epoxy
- Typical Properties
- Cured Properties
- Chemical Resistance
MEK (methyl ethyl ketone) Not Recommended Xylene 2 hours splash spill Gasoline 2 hours splash spill 10% sodium hydroxide 8 hours splash spill 50% sodium hydroxide 2 hours splash spill Acetic acid 5% 2 hours splash spill 10% sulfuric acid 2 hours splash spill 10% hydrochloric acid 2 hours splash spill 20% nitric acid Not Recommended Ethylene glycol 8 hours splash spill
| Value | Units | Test Method / Conditions | |
| Light Stability | Fair | - | - |
| Mechanical Stability | Excellent | - | - |
| Mixing Ratio | 4:1 | - | - |
| Set To Touch | 5 - 8 | hours | - |
| Solids | 52.0 | % | - |
| VOC Content | 175.0 | g/L | - |
| Water Resistance | Excellent, Beads Water | - | - |
| Value | Units | Test Method / Conditions | |
| Cure Rate (50°F, Dry to Touch) | min. 18 | hr | - |
| Cure Rate (50°F, Full Cure) | 14.0 | days | - |
| Cure Rate (50°F, Light Traffic) | 30.0 | hr | - |
| Cure Rate (77°F, Dry to Touch) | 4 - 5 | hr | - |
| Cure Rate (77°F, Full Cure) | 5 - 7 | days | - |
| Cure Rate (77°F, Light Traffic) | 16.0 | hr | - |
Regulatory & Compliance
- Slip Resistance
- Two recognized US agencies have issued directives on minimum coefficient of friction, OSHA (Occupational Safety and Health Administration) and Department of Justice through the ADA (Americans with Disabilities Act).
- ADA is the more stringent of the two. ADA directs that accessible walkways have a minimum coefficient of friction of 0.6. Ramps have been directed to be 0.8.
- The applicator assumes the responsibility to meet these standards. Areas that may become wet, oily, or greasy require special attention.
Safety & Health
- Caution
- Keep out of reach of children.
Inhalation:
- Avoid prolonged breathing of airborne dust, particularly present during mixing.
- Use NIOSH approved respirator for nuisance if threshold limit values are unsafe.
Skin Contact:
- Skin contact may cause irritation.
- Remove contaminated clothing and wash affected skin with soap and water.
- Launder clothing before reuse.
- If symptoms persist, seek medical attention.
Eyes:
- Wear safety eye protection when applying.
- Contact with eyes may cause irritation.
- Flush eyes with water for 15 minutes.
- If symptoms persist, seek medical attention.
Packaging & Availability
- Packing
Part “A” WTB (1-Gal Kit) SKU# 55102054 Part “A” DTB (1-Gal Kit) SKU# 55102055 Part “B” (1-Gal Kit) SKU# 55102058 Part “A” WTB (5-Gal Kit) SKU# 55102057 Part “A” DTB (5-Gal Kit) SKU# 55102056 Part “B” (5-Gal Kit) SKU# 55102059
Storage & Handling
- Shelf Life
Under normal, moisture free conditions 12 months for unopened container. ColorTec 600WB should not be exposed to freezing temperatures.
- Pot Life
1 hour