Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- The unique silane formulation creates the nano-sealer technology that deeply penetrates and reacts internally with cement, slowing moisture migration and efflorescence and intensifying bond capacity.
- Even in warmer climates HS 200LV’s slower evaporating solvents will not “cotton candy” before the applicator can finish a tight, smooth surface.
Applications & Uses
- Markets
- Applications
- Uses
A single coat application will provide a UV shield, enhance the beauty, and protect the surface of driveways, garage floors, patios, walkways, pool decks, and stucco.
- Coverage
Varies upon substrate: approximately 200 - 240 ft² per gal., per coat; 6.7 - 8 mils wet; 1.3 - 1.6 mils cured.
- Suitability Sample
- Due to condition specific sites, always prepare an adequate number of test areas.
- Wear protection system and esthetic suitability for products’ intended use should be included.
- On-site sample approval is especially critical on substantial, heavy traffic situation or custom coloration.
- Clean-Up
Before the product dries; spills and tools can be cleaned up with a solvent such as xylene or acetone.
- Limitations
- For use by trained professionals that have read the complete SDS.
- The product is strictly for interior use, upon a well-drained concrete slab with an appropriate vapor barrier, subject to no hydrostatic pressure.
- When masking use caution while taping to a floor that is not completely cured, especially at the edges, as delamination may occur.
- Protect from metal wheel traffic and some furniture where point of contact may be damaging.
- Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking
- Application Temperature
50 - 90 °F
Properties
- Appearance
- Clear (Wet), Clear Gloss Or Matte (Cured)
- Odor
- Solvent
- Chemical Properties
- Typical Properties
- Hot Tire Pick-Up*
- Under extreme circumstances, delaminating could occur.
- All tire manufacturers were not tested.
- Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking.
| Value | Units | Test Method / Conditions | |
| Brake Fluid | Remove Immediately | — | ASTM D-1308 |
| Formula 409 | Resistant | — | ASTM D-1308 |
| Gasoline | Remove Immediately | — | ASTM D-1308 |
| Motor Oil | Resistant | — | ASTM D-1308 |
| Transmission Fluid | Resistant | — | ASTM D-1308 |
| Value | Units | Test Method / Conditions | |
| Abrasion Resistance | 12.5 | g Loss | — |
| Adhesion (Dry Concrete) | Excellent | — | ASTM D-3359 |
| Adhesion (Wet Concrete) | Excellent | — | ASTM D-3359 |
| Block Resistance | Excellent | — | ASTM D-4946 |
| Blush (18hr Immersion ) | No Blush | — | — |
| Blush (4hr Dry) | No Blush | — | — |
| Diluents | Hydrocarbons | — | — |
| Film Formation (40°F) | Passed | — | — |
| Heat Stability (120°F) | Excellent | — | ASTM D-1849 |
| Hot Tire Pick-Up* | Passed | — | — |
| Light Stability | Excellent | — | — |
| Mechanical Stability | Excellent | — | — |
| Nano Technology | Silane Formulation | — | — |
| Pencil Hardness | HB-H | — | ASTM D-3363 |
| Solids | 20.0 | % | — |
| VOC Content | 400.0 | g/L | — |
| Water Absorption | 2.4 | g/m³ | — |
| Water Resistance | Excellent, Beads Water | — | — |
Regulatory & Compliance
- Slip Resistance
- Two recognized US agencies have issued directives on minimum coefficient of friction, OSHA (Occupational Safety and Health Administration) and Department of Justice through the ADA (Americans with Disabilities Act).
- ADA is the more stringent of the two. ADA directs that accessible walkways have a minimum coefficient of friction of 0.6. Ramps have been directed to be 0.8.
- The applicator assumes the responsibility to meet these standards. Areas that may become wet, oily, or greasy require special attention.
Technical Details & Test Data
- Weather Testing
- QUV accelerated
- ASTM G-53
- No blistering, no yellowing
- 250hours
Safety & Health
- Caution
- Keep out of reach of children.
Inhalation:
- Avoid prolonged breathing of airborne dust, particularly present during mixing.
- Use NIOSH approved respirator for nuisance if threshold limit values are unsafe.
Skin Contact:
- Skin contact may cause irritation.
- Remove contaminated clothing and wash affected skin with soap and water.
- Launder clothing before reuse.
- If symptoms persist, seek medical attention.
Eyes:
- Wear safety eye protection when applying.
- Contact with eyes may cause irritation.
- Flush eyes with water for 15 minutes.
- If symptoms persist, seek medical attention.
Packaging & Availability
- Available
Available in a clear gloss or matte finish.
- Packing
- 1 gal. (3.79 L) can
- 5 gal. (18.9 L) pail
- 55 gal. (208 L) drum
Storage & Handling
- Shelf Life
Under normal, moisture free conditions: 2 years for gloss finish, 1 year for matte finish in unopened container.