Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Base
- Synthetic Elastomers
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Field Of Application
Technicoll® 9110 is suitable for contact bonding of many plastics, especially for substrates difficult to bond like PE, PP and POM. technicoll® 9110 is highly resistant to moisture, aging and is characterized by a high initial tack and a long contact life.
- Favoured Substrates
- PE (HDPE, LDPE) PP, POM
- PA, PET, PETG
- PVC-n (unplasticised), PMMA, ABS, PS
- Polyester
- Derived timber products
- GFRP, CFRP
- Metals (blank, coated)
- Fabrics, leather, textile
- Rubber
- Glass
- Not suitable for: PE-films, PTFE (Teflon®), silicone, EPDM, plasticised materials (PVCplasticised), faux leather, PS-rigid foam (e.g. Styrofoam®)
- Due to the large variety of possible materials and differences in adhesion behavior hazard tests are mandatory before introducing the adhesive into the actual production process.
- Application & Uses
Surface preparation
Bonding surfaces must be dry and clean, especially free of oil, grease or release agents. In many cases, surface roughening prior to bonding improves strength of bonded joint. It is recommended when working with rubber and metals.
Adhesion
Stir adhesive before use. Apply a thin layer of technicoll® 9110 equally to both sides of the bonding surface of the substrates (brush, spraying gun). After the application solvent needs to evaporate. The usual waiting time is just a few minutes. It depends on the applied amount of adhesive and the indoor climate. The right time for the bonding has come as soon as the applied adhesive does not pull strings anymore when touching with the finger, but still feels very sticky. Join the substrates together accurately and assemble quickly under high pressure. The good bond strength that is achieved immediately, usually allows further processing with the bonded substances right away. Wait for a couple of days before assessing the final strength.
Way Of Application Two-sided Cleaning Agent / Material Technicoll® 8363 Cleaning Agent / Material (Metal Cleaning Spray) Technicoll® 9901 Cleaning Agent / Material (Plastics Cleaning Spray) Technicoll® 9902 Cleaning Agent / Tool (Technicoll® 8362, Spray) Technicoll® 9901 Cleaning Agent / Tool (Technicoll® 8362, Spray) Technicoll® 9901
Properties
- Typical Properties
- Handling Properties
- Behaviour At Low Temperature
Not susceptible to frost. Densification at low temperature. Once adjusted to processing temperature: fully employable.
- Handling Properties
Cleaning - Cured adhesive can only be removed mechanically.
| Value | Units | Test Method / Conditions | |
| Viscosity (20°C) | approx. 225 | mPas | — |
| Density | approx. 0.8 | g/cm³ | — |
| Application Temperature | 15 - 25 | °C | — |
| Temperature Resistance | approx. -20 to 80 | °C | — |
| Temperature Of Activation | approx. 80 | °C | — |
| Final Strength | min. 3 | days | — |
| Value | Units | Test Method / Conditions | |
| Drying Time | min. 10 | minutes | — |
| Contact Life | 50.0 | minutes | — |
| Way Of Application | Two-sided | — | — |
| Consumption (Two-sided Application) | 150 - 250 | g/m² | — |
| Cleaning Agent / Material | Technicoll® 8363 | — | — |
| Cleaning Agent / Material (Metal Cleaning Spray) | Technicoll® 9901 | — | — |
| Cleaning Agent / Material (Plastics Cleaning Spray) | Technicoll® 9902 | — | — |
| Cleaning Agent / Tool (Technicoll® 8362, Spray) | Technicoll® 9901 | — | — |
Storage & Handling
- Preferred Storage Temperature
- 10°C - 25°C
- Maximum Time Of Storage
At least 15 months when stored in sealed original packaging in cool and dry places.