Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features and Benefits
• Fast Cure – Dry to Touch in 15 Minutes.
• Thick Coating – One-Pass Application
• Fast & Easy Rework & Repair
• Meets IPC-CC-830
• Crystal Clear & Glossy Finish
• Contains Opti/Scan™, UV Indicator for Black Light QC Inspection
• Hazardous Air Pollutant Free: no MEK, Toluene or Xylene
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Applications
Electronic Assemblies for…
• Automotive
• Aviation
• Consumer Electronics
• Appliances
• Industrial Meters & Control- Usage Instructions
Surface to be coated should be thoroughly cleaned with a solvent such as Flux Remover G3® (1631). Surface must be completely dry before application of coating. Shake can well. Hold the board to be coated in a horizontal position and spray from top to bottom, holding the can four to six inches from surface. First, apply a light topical coating, then, after board has been fully coated, immediately apply a second heavier coat. Allow material to flow around the components. After application, invert can and spray until no liquid is expelled. Coating will be tack free in approximately 15 minutes; however, full cure requires 24 hours depending upon humidity. Complete removal can be achieved in 30 to 45 minutes by using the (2510) Conformal Coating Remover. Removal time depends upon temperature, thickness of coating and application.
Properties
- Physical Form
- Odor
- Characteristic
- Physical Properties
- Coating Properties
| Value | Units | Test Method / Conditions | |
| Vapor Density (Air=1) | min. 1 | — | — |
| Boiling Point | 230.0 | º F | — |
| Flashpoint and Method | 39.9 | ºF | TAG CC |
| Heat Combustion | 7.169 | kJ/g | — |
| Value | Units | Test Method / Conditions | |
| Product Benefits | Economical | — | — |
| Selective Spray System | Not recommended | — | — |
| Atomized Spray System | Acceptable | — | — |
| Dip | Acceptable | — | — |
| Aerosol Available | YES | — | — |
| Thermal Resistant | Acceptable | — | — |
| Moisture /Fungus Resistant | Acceptable | — | — |
| Chemical Resistant | Not recommended | — | — |
| Vibration Resistant | Acceptable | — | — |
| Ease of Rework | Excellent | — | — |
| 1 Aerosol Can (1.1M²) | 12.0 | ft² | — |
| Tack Free Time | 15.0 | minutes | — |
| Accelerated Cure Time/Temperature (2 Step, 120°F) | 20.0 | minutes | — |
| Accelerated Cure Time/Temperature (2 Step, 180°F) | 30.0 | minutes | — |
| Ambient Cure Time | 24.0 | Hrs | — |
| IPC-CC-830 Qualified | Yes | — | — |
| Solids Content (% by weight, Aerosol) | 6.1 | % | — |
| Solids Content (% by weight, Bulk) | 18.5 - 22.5 | % | — |
| Viscosity (Aersol) | 22.0 | cPs | — |
| UV Indicator | Yes | — | — |
| Operating Temperature Range | -65 to 125 | °C | — |
| Dielectric Strength | 2.08 | kV/Mil | — |
| Dielectric Constant | 3.1 | — | — |
| Insulation Resistance | 4 x 1013 | ohms | — |
| VOC (Aersol) | 29.0 | % | — |
Regulatory & Compliance
- Quality Standards
Safety & Health
- Environmental Policy
Techspray® is committed to developing products to ensure a safer and cleaner environment. We will continue to meet and sustain the regulations of all federal, state and local government agencies.
Packaging & Availability
- Thinning/ Removal
Techspray coatings can be thinned to meet production requirements using Conformal Coating Thinner (2105). Conformal Coating Remover (2510) is also available for rework and repair, although coating is often just burnt through in the soldering process for spot repairs.
- Packaging and Availability
2103-12S 12oz aerosol 12/case 2103-5G 5 gal (19L) 1/case
Storage & Handling
- Shelf Life
- 2 Years