Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Fast curing. ReVue-CRM is open to standard traffic within 4 hours of application and can be applied as thin as ¼”.
- High strength
- Interior and exterior applications
- One component
- Gains strength quickly
- Compatible with a wide range of temperatures
- Superior bond
- Better coverage
- Resistant to freeze and thaw conditions
- No VOC (0 g/L).
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Uses
Ideal for use in the following applications: warehouses, vertical repairs, truck docks, heavy industrial repairs, commercial floors and ramps. With its capability to withstand extreme temperatures, ReVue-CRM is ideal for fast track projects in high traffic areas including streets and truck docks.
- Limitations
Do Not Use:
1. Where hydrostatic pressure (water) exists or moisture emissions exceed level permitted for installing floor covering.
2. Over presswood, particle board, Masonite, chipboard, OSB, underlayment board not of APA Underlayment (exterior) grade or similar dimensionally unstable materials susceptible to movement or swelling.
3. Over gypsum based patches or underlayment material due to chemical reaction.
4. Single layer stripwood floors.- Application Equipment
Protective clothing Trowel (stainless steel), 4" x 12" (101.6 x 304.8 mm) Pool Trowel or 3” x 12” (76.2 x 304.8 mm) finishing trowelsMortar mixer – [Baugh, Imer or Kol mixer]Assemble Equipment: Due To The Limited Pot Life Of The Material, All Application Equipment, Etc. Should Be Ready For Immediate Use. (Clean Roller With Tape To Remove Any Residual Lint.)
Cleanup: Use Water To Clean Revue-crm From Tools And Equipment. Once It Is Dry It Will Need To Be Removed Mechanically. It Is Important To Periodically Clean Tools.
- Surface Preparation
The concrete surface should be clean and sound. The surface should be free of any bond breakers including but not limited to loose gravel, oil, wax, grease or dirt. Concrete with cap intact that is being overlayed to change slope, etc. needs to be aggressively blasted with shot or scarified. The concrete should be presoaked and saturated surface-dry SSD condition without standing water.
- Applications
Coverage Rate:
Coverage Rate Will Depend Upon Application Thickness. A One Bag Mix Will Nominally Cover (Finished Floor):
Revue-crm: 9.6 Ft2 @ 1/2" (0.89 M2 @ 12.7 Mm)
Note: Do Not Apply Less Than ¼” In Thickness Or Where Featheredge Is Needed.
Pour One-half Gallon Of Water Into The Mortar Mixer. Begin Mixing.
While Mixing Slowly Add One Bag (55 Lbs) Of Concrete Repair Mortar Over 3-5 Minutes To The Water In The Mortar Mixer. Note: For Deeper Patches (>1”), Revue-crm May Be Extended By Adding Up To 30 Pounds Of Clean Pea Gravel. A Small Amount Of Additional Water May Be Added Only After 2 Minutes Of Mixing; No More Than One Cup.
Do Not Over Mix Due To The Formation Of Air Bubbles.
Working Time: Approximately 20 Minutes At 72°f (22.2°c).
Pour The Mixed Material On The Prepared Area.
Use Hand Trowels To Compact And Level Material. Firmly Work The Material Into The Bottom Ensuring A Good Bond.
Set Time Of Material Is 30-45 Minutes.
Allow Material To Cure 4 Hours Before Opening To Traffic.- Applications of Additional Coatings
The repair mortar needs to be mechanically prepped, or coatings will not adhere well. The repair mortar needs to cure >12 hours before it will be hard enough; this will vary with cure conditions.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Direct Shear Bond (1 Day) | 155.0 | psi | — |
| Direct Shear Bond (28 Day) | 445.0 | psi | — |
| Direct Shear Bond (7 Day) | 380.0 | psi | — |
| Freeze & Thaw Resistance (RDM) | 97.0 | % | — |
| Open to Traffic | 4.0 | hours | — |
| Rapid Chloride Permeability (Low) | 1050.0 | — | — |
| Set Time | 30 - 45 | minutes | — |
| Slant Shear Bond (1 Day) | 1900.0 | psi | — |
| Slant Shear Bond (28 Day) | 3300.0 | psi | — |
| Slant Shear Bond (7 Day) | 2900.0 | psi | — |
| Strength (1 Day) | 4500.0 | psi | — |
| Strength (28 Day) | 7000.0 | psi | — |
| Strength (3Hours) | 1200.0 | — | — |
| Strength (7 Day) | 6000.0 | psi | — |
| Volatile Organic Compound (VOC) | 0 (0.0) | — | ASTM D3960 |
| Working Time | 20.0 | minutes | — |
Regulatory & Compliance
- Certification
LEED® CREDIT – LEED Green Building Certification Program credits may be available:
Indoor Environmental Quality
- 4.2 Low-Emitting Materials, Paint & Coatings
- Material and Resource
- 4.1 / 4.2 Recycled Content, 10% / 20%
Safety & Health
- Preliminary Floor Inspections
Check The Temperature: Floor Temperature And Materials Need To Be Above 50-90°f (10-32° C). Note: Higher Temperature Application Will Yield Shorter Work Times.
Check The Concrete: Concrete Must Be Structurally Sound. Tennant Assumes No Liability For Substrate Defects. If You Suspect The Concrete Has Been Sealed Or Coated, Call Tennant Company Tech Support For Further Instructions.
Check For Moisture: Concrete Must Be 28 Days Old Before Application Of This Material. Concrete Moisture Testing Must Occur. In-situ Relative Humidity Testing Is Recommended. Readings Must Be Below 75% Relative Internal Concrete Humidity. Test Methods Can Be Purchased At Www.astm.org, See F2170, Or Follow Manufacturer's Instructions. If Moisture Issues Are Present, The Use Of A Moisture Mitigation System May Be A Consideration. Please Call Tennant Company Technical Support For Further Information / Instructions.
Packaging & Availability
- Packaging Type
- Application Characteristics
Thickness ¼” to 4”(6.35 mm to 101.6 mm)Coverage Rate per bag mix 9.6 ft2 @ ½” (0.89 m2 @ 12.7 mm)- Packaging Options/ Part Numbers
ReVue-CRM
9013209 (Pallet of 48 - 50 lb. doublé-wall bags)
Note: Mix with exactly ½ gallon (1.89 liters) of potable wáter. DO NOT OVER WATER.
Storage & Handling
- Storage
Materials should be stored indoors between 65ºF (18ºC) and 90ºF (32ºC).
- Shelf Life
One year from date of manufacture.
- Disposal
Dispose of all excess material, packaging and other waste in accordance with federal, state and local regulations.