Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Good resistance to many common chemicals
- Monolithic installation with integral cove base
- Self-priming product (except troweled applications)
- Provides a highly durable and protective flooring system
- Installed by approved applicators
- No offensive odors during installation
- USDA approved
- Volume mix ratio: 2:1
- Limitations
- Direct sunlight will cause some discoloration
- Requires a protective top coat
- Must be installed on dry surfaces only
- Only available in normal cure
- Limited substrate temperature range during installation
- Not suitable in areas of harsh chemical use
- Does not contain same pigment load as top coat systems
Applications & Uses
- Markets
- Applications
- Application Method
- Application
- 730 ArmorBond is formulated specifically for interior use on dry substrates and in application temperatures at not less than 13oC (55oF); and meets VOC regulations.
- 730 ArmorBond is a self-priming system for slurry applications or can be applied neat as a primer for troweled overlays. This system can be installed with a monolithic cove base to create a seamless and sanitary installation that complies with USDA regulations.
- For best application results, pre-condition the material to between 80°F (27°C) and 90°F (32°F) if the substrate temperature is below 70°F (21°C).
Degrees Recoat Time 60°F 8-9 hrs. 77°F 14-16 hrs. The above table assumes ambient temperature, material and substrate are equal and material is applied at 20 mils in thickness.
- Product Application
The ArmorBond Base Coat System can be applied over the VaporGard Coating System in applications where hydrostatic or vapor transmissions could be a potential hazard; and can be used with any of the Thermal-Chem complimentary and repair products; and can be applied as a:
- Slurry or Slurry/Broadcast System - typically 1/16" thickness or greater
- Troweled Overlay System - typically 3/16" thickness or greater
- Uses
Typical uses for the 730 ArmorBond Base Coat System include:
- Industrial flooring
- Warehouse aisle ways
- Some processing facilities
- Wastewater treatment facilities
- Laboratories
- Commercial kitchens
Wherever the following flooring properties may be necessary:
- Slip-resistant surface
- Increased ease of maintenance
- Good abrasion resistance
- Durability and sanitary protection
Properties
- Physical Properties
| Value | Units | Test Method / Conditions | |
| Hardness | 80 - 85 | Shore D | ASTM D2240 |
| Bond Strength (100% con. failure) | max. 350 | — | ACI 503 |
| Impact Resistance | 160.0 | in./lbs | ASTM D2794 |
| Abrasion Resistance | 33 - 35 | mg. | ASTM D1044 |
| Tabor Abrasion (CS-17 Wheel 1000 gms. Load 1000 cycles) | Loss | — | — |
| Viscosity (77°F) | 500 - 700 | cps | — |
| Viscosity (60°F) | 1300 - 1600 | cps | — |
| Compressive Strength | 10800.0 | — | ASTM D695 |
| PSI (7 Day Cure Aggregate Filled) | 12600.0 | — | — |
| Compressive Modulus | 277300.0 | — | ASTM D695 |
| Flexural Strength | 14370.0 | — | ASTM D790 |
| Modulus | 416000.0 | — | — |
| Tensile Elongation | 5.0 | % | ASTM D638 |
| Tensile Strength | 9240.0 | — | — |
| Tensile Modulus | 440900.0 | — | — |
| Freeze Thaw Resistance (300 Cycles) | Passes | — | ASTM C666 |
Regulatory & Compliance
- Certifications & Compliance
Safety & Health
- Product Handling
Warning : For professional use only. Avoid contact of uncured material with skin and eyes. Contact with skin may result in irritation. Wash skin with soap and water. If contact with eyes should occur, flush with water for 15 minutes and seek immediate medical attention.
Packaging & Availability
- Color and Textures
- Various slip-resistant textures available
- May be field pigmented using Thermal- Chem’s ColorThane universal pigment.
- 730 ArmorBond is available in normal cure only.