Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Advantages
- Low VOC
- Designed specifically for tub and tile refinishing
- State of the art gloss and color retention
- Excellent chemical, stain, and abrasion resistance
- Excellent flexibility, chip, and scratch resistance
- Extremely durable; resistant to acidic etching
- Easy to clean and repair
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Uses
Liquid Porcelain is ideal for use on:
- bathtubs and shower stalls
- bathroom and kitchen countertops and sinks
- countertop backsplash areas
Product results will vary by substrate and application method. it is the user’s responsibility to determine the suitability and performance of this product for their application.
- Limitations
- Not recommended for immersion into gasoline, diesel, hydraulic fluids or solvents
- Proper surface preparation required
- Maximum RH at worksite: 75%
- Application Data
SURFACE PREPARATION:
All surfaces must be clean, dry, and free of contaminants. All dirt, grease, rust, mill scale, or loose chalky paint must be removed. Surfaces must remain dry and protected from all moisture until fully cured.
Fiberglass and previously painted surfaces must be sanded to dull. Finish sanding surfaces with a very fine 400-600 grit sandpaper; dry brush or vacuum to remove all dust. All substrates must be primed or pre-treated.
APPLICABLE SUBSTRATES: [when properly prepared]- porcelain
- fiberglass
- Formica
- cast polyester
- most metals
- steel
RECOMMENDED PRIMERS:
- 283P309 Aquapoxy™ Primer
- 983P746 TriBond - Liquid Porcelain™ achesion promoter
- 941FAM35 Epoxy Primer - Liquid Porcelain™
Consult Triangle Coatings for other primer recommendations.
APPLICATION TEMPERATURE:- Substrate must remain 10° F above the dew point during application and for 24 hours after application.
- Not recommended for substrate temperatures below 50° F or above 100° F.
- Mixing Parametres
Ratio [PartA: Part B] By Weight [LP249G700 . 4.02: 1.00 By Volume ..... . 4.00: 1.00 Sweat-in Time: none - Application Method
Liquid Porcelain can be applied by HVLP or air assist airless For other types of application, please contact your Triangle Coatings representative. This product should be applied in two distinct coats to avoid pinhole voids.
HVLP:
Fluid Tip and Needle: .030 - .040”
Fluid Pressure: 10-15 psi
Air Cap Pressure: 60 psi
Air Assist Airless:
Fluid Tip:012-013"
Fluid Pressure: 900-1400 psi
Air Cap Pressure: 10 psi
Airless: No
Brush or Roller: Limited
Thinning: AT75
Add Part B before reducing. For conventional spray, reduce 10-15% by volume.
CleanUp: AT75*
Clean tools while Liquid Porcelain is still wet.
*ONLY AT75 may be used to clean or thin this product.
Properties
- Properties
REQUIRED FILM THICKNESS: ASTM D1005 Minimum Dried Film 1.5 mil (38μ) ASTM D4414 Minimum Wet Film 3.0 mil (76μ) ASTM D523 GLOSS: @ 60° 90 @ 20° 75 ASTM D3363 PENCIL HARDNESS: 3H Pass ASTM D5402 MEK RUBS: 200 Double Pass ASTM D2794 IMPACT RESISTANCE: 160 inlb forward, 160 inlb reverse Pass ASTM B117 SALT SPRAY RESISTANCE: 5% Salt Spray, 150 hours [BondRite 1000] Pass ASTM D5894UV CORROSION WEATHERING: ASTM D610 Rusting 7 cycles, 150 hours Pass ASTM D714 Blistering 7 cycles, 100 hours Pass ASTM D4587/D523/D4214 QUV-UVA: 500 hours @ 60° 10% loss 1000 hours @ 60° 20% loss ASTM D2247/D714 HUMIDITY RESISTANCE: 400 hours [unscribed] Pass ASTM D4585 MOISTURE CONDENSATION: 100° F, 400 hours Pass ASTM D3359 ADHESION: 5B Pass ASTM D4060 ABRASION RESISTANCE: CS17 wheel, 110 cycles, 1 kg load < 10 mg ASTM D522 FLEXIBILITY: 180° bend, 1/4” mandrel Pass ASTM D3170 CHIP RESISTANCE: Rating N/A ASTM D2485 DRY HEAT RESISTANCE: 200° F Pass WET HEAT RESISTANCE: 180° F Non-immersion Pass ASTM D2243 WATER-BORNE FREEZE THAW: 3 cycles N/A
Technical Details & Test Data
- Dry Schedule
DRY SCHEDULE: [at 50% RH and 1.5 mil DFT] 60° F 77° F 90° F Dry to Touch 60 mins 45 mins 25 mins Recoat 8 hrs 2 hrs 60 mins Dry to Handle 8 hrs 2 hrs 60 mins Full Cure 7 days 7 days 7 days Critical Recoat Window: After one week light sanding may be
necessary if coating is subject to extended exterior exposure.- Coverage
Theoretical at 1.5 mil DFT: 620 sq ft/gal
Safety & Health
- Health and Safety Precautions
Warning:
FLAMMABLE LIQUID AND VAPOR. DO NOT INGEST. May be harmful if swallowed or inhaled. Vapor may affect the brain ornervous system causing dizziness, headache, ornausea and can cause nose and throatirritation. Liquid contact with eye and skin causes irritation. Keep away from sparks, heat, or open flame. Use with adequate ventilation. Avoid breathing of vapor. Avoid contact with eyes and skin. Wash hands thoroughly after using and before eating and smoking. Wear an appropriately fitted respirator (NIOSH/MSHA approved) during and after application unless air monitoring demonstrates vapor levels are below applicable limits. Keep container closed when not in use. If spillage occurs, absorb and dispose of according to local regulations.
Contains:- aromatic hydrocarbon mixture, CAS#64742-95-6
- bis 1,2,2,6,6-pentamethyl-4-piperdinyl, CAS#41556-26-7
- 4-chlorobenzotrifluoride, CAS#98-56-6
- homopolymer of HDI, CAS#28182-81-2
- n-butyl acetate, CAS#123-86-4
- propylene glycol methyl ether acetate, CAS#108-65-6 polyol
- xylene, CAS#1330-20-7
First Aid:
Should eye contact occur, flush with plenty of water for at least 15 minutes and get medical attention if vision is disturbed. For skin, wash thoroughly with soap and water. If swallowed, seek medical attention immediately. DO NOT induce vomiting.
Notice:
Intentional misuse by deliberately concentrating and inhaling the contents may be harmfulorfatal. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. This product does not contains materials listed in California Proposition 65.
KEEP THIS PRODUCT OUT OF REACH OF CHILDREN.
Packaging & Availability
- Color Availability
Liquid Porcelain is stocked in white and black, in three gloss levels. Custom colors available; minimum order is required. Special costing will be applied.
- Order Code
[Mix Ratio: 4 Part A:1 Part B, by volume]
PartA [base]: LP249 + gloss + color
Part B [activator]: LP249B
Individual products are identified by the product series number, followed by a gloss identifier and color number. LP249G700 is Liquid Porcelain, Gloss, White.
This product is available in:
Gloss: G
Semi-Gloss: S
Low semi-gloss: M- Packaging
This product is packaged in kits, containing both PartAand Part B components. Kit containers may be partially filled to obtain total yeild when mixed.
Total Yeild: Part A: Part B: 40 ounces 1 quart can 1 half pint can 1.25 gallons 1 gallon can 1 quart can 1 quart* *Southern California Air Quality Management District regulates this product only be purchased/used in quartsizes or smaller. Sizes larger than 1 quart may NOT be purchased for use as an Architectural or Maintenance coating in regions with these regulations.
Storage & Handling
- Pot Life
ASTM D2196 Pot Life: [valid for qtys of 1 gallon or more]
50° F 65° F 77°F 85° F 5 hrs 4 hrs 4 hrs 3 hrs - Shipping and Handling
- SHIPPING DESCRIPTION: [CFR 49]
Ground, Air, Vessel Paint, 3, UN1263, PG IIIRequired Label FLAMMABLE LIQUIDRequired Marking PAINT UN1263 IMDG PACKAGING:FLAMMABLE LIQUID, class 3.3, UN1263, IIIIMDG STOWAGE: Category A UNIFORM FIRE CODE: [CFR 29] CLASS II STORAGE TEMPERATURE: 120° F max SHELF LIFE: [warranted] 1 YEAR HMIS RATINGS: H - 2; F - 3; R - 0; PP - H