Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Product Highlights
TriBond W is a high performance primer for:
- zinc
- galvanizing
- inorganic zinc rich
- copper
- brass
- aluminum
- steel
- Advantages
- Very fast dry
- Compatible with epoxy, urethane, and other strong solvent topcoats
- Excellent resistant to moisture, abrasion, acids, alkalis, and other chemicals
- Good adhesion to properly prepared substrates
- Contains no lead or chromate
- Low toxicity
- Water cleanup
Applications & Uses
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Uses
TriBond W is ideal for use on:
- shop finished architectural components
- heavy construction equipment
- off road vehicles
- light rail applications
- farm implement equipment
- other miscellaneous metal parts
Product Results will vary by substrate and application method. itis the user’s responsibility to determine the suitability and performance of this product for their application.
- Limitations
- Not for immersion
- Must be topcoated for exterior use
- Limited below grade use; contact Triangle for more
- information regarding application
- Requires adequate topcoat film build to prevent epoxy
- deterioration and topcoat delamination
- Maximum RH at worksite: 75%
- Application Data
Surface Preparation:
All surfaces must be clean, dry, and free of contaminants. All dirt, grease, rust, mill scale, or loose chalky paint must be removed.
Recommended surface preparation includes:- surface blasting to remove all mill scale (maximum profile: 0.5-1.0 mils) iron phosphate* (35-40 milligrams per square foot)
- zinc phosphate* (25-30 milligrams per square foot)
- seal coat or DI final rinse recommended
APPLICABLE SUBSTRATES: [when properly prepared]
- ferrous or non ferrous
- primed galvanized
- primed aluminum
- concrete
APPLICATION TEMPERATURE:
- Substrate must remain 10° F above the dew point during application and for 24 hours after application.
- Not recommended for substrate temperatures below 50° F or above 100° F.
- Mixing Parametres
Ratio: [PartA: Part B] By Weight . 2.37: 1.00 By Volume . 2.00: 1.00 Sweat-in Time 10 minutes - Application Method
TriBond W can be applied by HVLP, air assist airless, or airless spray. For other application methods, please contact your Triangle Coatings representative.
HVLP:
Fluid Tip and Needle: 030 - .040”
Fluid Pressure: 10-15 psi
Air Cap Pressure: . 60 psi
Air Assist Airless:
Fluid Tips: 012 - .013”
Fluid Pressure: . 900-1 ,400 psi
Air Cap Pressure: 10 psi
Airless:
Fluid Tips: 013 - .015”
Fluid Pressure: 2,000-2,500 psi
Brush or Roller: limited; small areas only
Thinning: water; 1-2% by volume
CleanUp: water
Clean tools with detergent and water while TriBond W is still wet.
Properties
- Properties
REQUIRED FILM THICKNESS: ASTM D1005 Minimum Dried Film 2.0 mil (51μ) ASTM D4414 Minimum Wet Film [2 coats] 5.3 mil (135μ) ASTM D523 GLOSS: @ 60° 44783 @ 20° N/A ASTM D3363 PENCIL HARDNESS: HB-H Pass ASTM D5402 MEK RUBS: 200 Double Pass ASTM D2794 IMPACT RESISTANCE: 20 inlb forward, 20 inlb reverse Pass ASTM B117 SALT SPRAY RESISTANCE: 5% Salt Spray, 800 hours [BondRite 1000] Pass ASTM D5894UV CORROSION WEATHERING: ASTM D610 Rusting 7 cycles, 500 hours Pass ASTM D714 Blistering 7 cycles, 800 hours Pass ASTM D4587/D523/D4214 QUV-UVA: 500 hours @ 60° N/A 1000 hours @ 60° N/A ASTM D2247/D714 HUMIDITY RESISTANCE: 800 hours [unscribed] Pass ASTM D4585 MOISTURE CONDENSATION: 100° F, 1000 hours Pass ASTM D3359 ADHESION: 5B Pass ASTM D4060 ABRASION RESISTANCE: CS17 wheel, 110 cycles, 1 kg load < 10 mg ASTM D522 FLEXIBILITY: 180° bend, 1/4” mandrel Pass ASTM D3170 CHIP RESISTANCE: Rating N/A ASTM D2485 DRY HEAT RESISTANCE: 200° F Pass WET HEAT RESISTANCE: 180° F Non-immersion Pass ASTM D2243 WATER-BORNE FREEZE THAW: 0 cycles Protect from freezing
Technical Details & Test Data
- Dry Schedule
DRY SCHEDULE: [at 50% RH and 2.0 mil DFT] 60° F 77° F 90°F Dry to Touch 50 mins 20 mins 5 mins Recoat 90 mins 45 mins 15 mins Dry to Handle 2 hrs 40 mins 20 mins Full Cure 7 days 7 days 7 days Critical Recoat Window: After 2 days, must sand or blast
surface and reprime.- Coverage
Theoretical at 2.0 mil DFT: 305 sq ft/gal
Safety & Health
- Health and Safety Precautions
Warning:
LIQUID CONTACT WITH EYE AND SKIN MAY CAUSE IRRITATION. DO NOT INGEST. Avoid contact with eyes and skin. Wash hands thoroughly after using and before eating and smoking. Keep container closed when not in use. If spillage occurs, absorb and dispose of according to local regulations.
First Aid:
Should eye contact occur, flush with plenty of water for at least 15 minutes and get medical attention if vision is disturbed. For skin, wash thoroughly with soap and water. If swallowed, seek medical attention immediately. DO NOT induce vomiting.
Notice:
Intentional misuse by deliberately concentrating and inhaling the contents may be harmfulor fatal. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. This product does not contains materials listed in California Proposition 65.
KEEP THIS PRODUCT OUT OF REACH OF CHILDREN.
Packaging & Availability
- Color Availability
TriBond W is stocked in medium yellow. Custom colors available; minimum order is required. Special costing will be applied.
- Order Code
966P + color Individual products are identified by the product series number, followed by an identifier and color number. Ex: 966P309 is TriBond W, Medium Yellow.
- Packaging
- 1 gallon cans
- 5 gallon pails
- 55 gallon drums
Storage & Handling
- Pot Life
ASTM D2196 Pot Life: [valid for qtys of 1 gallon or more]
50° F 65° F 77° F 85° F 8 hrs 5 hrs 4 hrs 2 hrs - Shipping and Handling
SHIPPING DESCRIPTION: [CFR 49] Ground, Air, Vessel Not Regulated Required Label Not Required Required Marking Not Required IMDG PACKAGING: Not Required IMDG STOWAGE: Not Regulated UNIFORM FIRE CODE: [CFR 29] CLASS III-B STORAGE TEMPERATURE: 120° F max KEEP FROM FREEZING SHELF LIFE: [warranted] 1 YEAR HMIS^{®} RATINGS: H - 1; F - 1; R - 0; PP - B