company tower banner
UC Coatings Company Logo

UC Coatings Stay Clean Moss & Algae Prevention Solution - Concentrate

UC Coatings Stay Clean Moss & Algae Prevention Solution - Concentrate contains a mold and algae inhibitor that protects the film it forms on substrates from microbes. Stay Clean’s water-based acrylic binder chemistry will adhere to most porous surfaces. It is delivered in concentrated form and is easy to dilute, mix, and apply. Stay Clean combines high performance, ease of use and consumer safety with the environmentally-friendly benefits common to water-based technologies.

Product Type: Coating

Features: Corrosion Resistant, Ease of Handling, Good Adhesion, Low Odor, Low VOC

Compatible Substrates & Surfaces: Composites, Concrete, Metal, Wood

Application Method: Spray

  • TypeDocument Name
View All Documents

Knowde Enhanced TDS

Identification & Functionality

Product Type

Features & Benefits

Features
  • Effective mold, moss & algae inhibitor
  • Adheres to most porous surfaces
  • Cleans up with soap & water
  • Extends roof life
  • Easy to mix concentrate 1:1 with water
  • Apply with garden sprayer, air-assisted or airless sprayer
  • Dry to the touch in one hour
  • Dries clear
  • Non-corrosive
  • Ultra-low VOC’s & low odor
  • 3-year product replacement warranty

Applications & Uses

Application Method
Compatible Substrates & Surfaces
Greater Use on
  • Roofs: Composite-Shake-Tile
  • Wood: Fencing-Decking-Furniture
  • Concrete Walkways & Walls
  • Pavers & Stone
  • Brick & Mortar
  • Cement Block
  • Tile & Grout
Applications

Surface Preparation

  • All surfaces should be clean and dry before application. Remove dirt, debris, moss, mold, algae, fungi, and mildew.

Application

  • Apply only at temperature above 45 degrees F and below 95 degrees F. Do not apply in rain or when rain is expected within 6-8 hours.
  • For 55-gallon drums and 275-gallon totes: Prior to adding water mix Stay Clean thoroughly for 20-40 minutes.
  • For 5-gallon pails: Prior to adding water mix Stay Clean thoroughly for 2-3 minutes.
  • Mix 1:1 with water in a plastic or metal container.
  • Use low pressure sprayer such as a garden sprayer to apply. An air-assisted or airless sprayer may also be used.
  • Apply enough Stay Clean until it starts to run (flood coat). Make sure all cracks and crevices are well coated.
  • Surface may be used or walked on after 6-8 hours (depending on temperature and humidity).

Safety & Health

Precautions
  • Use with adequate ventilation. Keep out of the reach of children. Close container after use. If spraying, use an approved NIOSH/MSHA respirator.  Avoid contact with eyes. If splashed into eyes, rinse with clean water for 15 minutes. If skin irritation occurs, wash area with soap and water. Do not take internally. If accidently ingested, immediately drink two glasses of water and contact a physician, do not induce vomiting

Packaging & Availability

Packaging Information

Packaging Sizes

  • 5 Gallon Pails (18.9 Liters)
  • 55 Gallons Drums (208.2 Liters)
  • 275 Gallon Totes (1041 Liters)

Coverage

  • 5 Gallon Pail: Approximately 4,000 square feet.

Storage & Handling

Storage Information

Cleanup & Storage

  • Clean tools and equipment with soap and water immediately after use.  Store above 32 degrees F to protect from freezing.

Disposal

  • Never pour leftover material down a drain or sink. Use up material on the job or seal container and store safely for future use. Do not incinerate closed containers. For specific disposal guidelines contact your local waste management agency.