Ultrakote Products Shurgard RA - Ease of Handling

Enhanced TDS

Knowde-enriched technical product data sheet

Identification & Functionality

Product Type: Elastomeric Coating
Technologies: Ready-to-Use Products
Product Families: Ready-to-Use Products — Paints & Coatings
Protective Coatings
Classification: Barrier - Type III air

Features & Benefits

Ready-to-Use Product Features: Ease of Handling,
Improved Adhesion,
Moisture Barrier,
Water Resistant
Features and Benefits: Features:

Ease of application

Economical

Promote adhesion

Benefits:

Rolled or brush on application

No waste-reseal for use later

Superior substrate for adhesively applied EPS

Applications & Uses

Markets: Building & Construction
Applications: Building & Construction — Building Envelope & Roofing
Architectural Coatings
Application Method: Brush,
Roller
Uses: Shurgard RA can be applied over a wide variety of substrates such as exterior grade gypsum sheathing, cement board and OSB. Shurgard ra is applied as a continuous membrane utilizing Ultrakote 4” Transition Mesh without voids or pinholes.
Surface Preparation: Surface must be clean and free of bonding-inhibiting materials such as dirt, dust, rust, grease, oil, efflorescence, mildew, fungus, form-release agents or any other contami- nants. Remove and repair any loose paint, mortar, stucco, concrete or masonry by water blasting, sand blasting, scraping or using a wire brush.
Coverage: Average coverage rates per mixed pail are:

Dens Glass Gold: 400 - 500 F² (37.1 - 46.5 m²)

Exterior Grade Gypsum Sheathing: 450 - 550 F² (41.8 - 51.1 m²)

Cement Boards: 375 - 475 F²(34.8 - 44.1 m²)

OSB or Plywood: 225 - 325 F² (21 - 30.2 m²) (Two coats required)
Clean Up: Clean tools and equipment with water immediately after use.
Mixing: Shurgard RA is ready to use, simply thoroughly mix the pail prior to application. No water or additives should ever be added.
Application: Use a synthetic brush or heavy nap roller and always use clean tools and equipment. Shurgard RA is rolled or sprayed over the approved substrate at 12 mils wet film thickness - 6 mils dry film thickness. OSB requirestwo coats to achieve sufcient coverage. Check the surface to ensure there are no voids or pinholes. Completely embed Ultrakote 4” Transition Mesh at all board joints and transitions to ensure a continuous barrier.
Curing: Allow Shurgard RA to cure for 24 hours prior to applying the EPS insulation board.
Limitations: Shurgard RA should be applied when surface and ambient conditions are between 40ºF (4.4ºC) and 95ºF (35ºC).

Properties

Typical Properties

	Value	Units	Test Method / Conditions
Air Leakage (Installed Over Dens Glass Gold)	0.013	1/s/m²	ASTM E283
Flame Spread	max. 450	-	ASTM E84
Flammability	max. 25	-	-
Flexible Mandrel Bend (40°F, 4” Mandril)	Passes	-	ASTM D522
Hydrostatic Pressure Resistance (12” head)	Pass	-	-
Smoke Developed	A	-	-
Tensil Bond Strength (Cement Board)	28.7	psi	ASTM C297
Tensil Bond Strength (Dens Glass Gold)	37.4	psi	ASTM C297
Tensil Bond Strength Gypsum Sheathing	13.5	psi	-
Water Vapor Transmission	avg. 2 - 3	perms	ASTM E96 Method B

Technical Details & Test Data

Weather Resistance: No deleterious e ects after 14 days exposure

Safety & Health

Safety: Precaution: Keep out of the reach of children. Not for internal consumption. Do not apply in non-ventilated areas. Use protective equipment such as gloves, eye protection and clothing.

First Aid:

In case of eye contact, flush with water at least 15 minutes.

In case of skin contact, wash afected areas with soap and water. If irritation persists, Seek medical attention. Remove and wash contaminated clothing.

If inhalation causes physical discomfort, remove to fresh air. If discomfort continues, any breathing dificulty occurs or if swallowed, Seek medical attention.

Disposal: Dispose of in accordance with local, state or federal regulations.

Warning: Keep out of the reach of children. Not for internal consumption, for industrial use only.

Spills: Scrape up and wash with water immediately. If material has set, scrape material with appropiate tools and clean with citric acid.

Prop 65: This product contains material listed by the state of California known to cause cancer, birth defects or other reproductive harm.

Packaging & Availability

Packaging Type: Pails
Packaging: 5 gallon plastic pail 50 lbs. (22.6 kg)

Storage & Handling

Shelf Life: 1 year
Storage: Keep from freezing, keep out of direct sunlight for long periods and store at temperature ranges between 40ºF (4.4ºC) and 95ºF (35ºC)