Knowde Enhanced TDS
Identification & Functionality
- Carrier
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Fast Drying
- Penetrating
- Colors can be Blended for Unlimited Color Selection
- Safe to Ship via UPS
- Great Interior Color Fastness
- Easy to Use
- Can be Sealed with Both Solvent and Water-Based Sealers
- No Rinsing Needed
- Can be Used with Polished Concrete
Applications & Uses
- Markets
- Application Method
- Compatible Substrates & Surfaces
- Uses
- When mixed with acetone, SC-36 can be used as a primary coloring application for polished concrete as well as grind, stain and seal systems.
- SC-36 may be used in conjunction with Acid stains as a secondary coloring system.
- Fast Stain is designed for interior use only.
- Inspection
- Substrate must be clean, dry, and free of grease, paint, oil, dust, sealers, wax, curing agents, or any foreign material that will prevent proper adhesion.
- Not intended for exterior applications.
- Moisture
- All concrete should be tested for moisture before applying a seamless coating.
- If moisture emissions exceed 5 lbs/1000 square feet/24 hours (ASTM F1869) or if the relative humidity (RH) exceeds 75% (ASTM F2170), contact the manufacturer before application.
- Preparation
- For concrete, the surface should be at least 2500 psi and have cured for a minimum of 28 days.
- Prior to starting work, test existing concrete slab for efflorescence, moisture and hydrostatic pressure.
- Methods of preparation may vary according to the desired outcome.
- Factors include the forecasted use of the surface, the environment in which it is to be installed and if a sealer will be used. When preparing the surface, take in to consideration the desired final look and prep accordingly.
- Mixing
- For ease of mixing, begin by adding a small amount of acetone into the SC-36 Fast Stain powder container.
- Pour approximately 6 ounces of acetone into the half-pint container of pre-measured Fast Stain powder (1 gallon mix) or 12 ounces of acetone into the pint container of pre-measured Fast Stain powder (5 gallon mix).
- Replace the lid and shake to dissolve the powder.
- Once powder has dissolved, place a funnel in the opening of the 1 or 5 gallon acetone and pour contents of first mix into remaining acetone.
- Shake entire mixture and let sit for 15 minutes, shake again and the Fast Stain is now ready to apply.
- Colors may be varied by adding more or less acetone.
- Thinning
Do not thin.
- Coverage
- The coverage will vary depending on the surface.
- Up to 400 square feet per gallon on a smooth surface and between 150-250 square feet on rough surfaces.
- Applying Product
- Applying Product Before beginning any project, it is recommended that a mock-up be installed to help indicate the overall look and finish.
- Material may be applied with a solvent safe sprayer.
- For best results, use a solvent safe, pump sprayer with a conical tip.
- Be sure to apply evenly and consistently with an overlapping circular or figure eight pattern.
- Avoid puddling the stain.
- Additional coats may be applied after the first coat has dried for 10 to 20 minutes.
- Additional coats will produce a darker color.
- Multiple colors may be layered or sprayed at the same time to create a variegated finish.
- Be sure to paper/plastic off any areas that you do not want dyed.
- SC-36 may leave residual dye on the surface after application.
- If this occurs, it is recommended to remove excessive dye.
- A white pad may be used “dry” on a floor machine to remove residue, then a dust mop or vacuum can be utilized to collect the residual dye.
- Be sure to extinguish all pilot lights and sources of ignition.
- Ventilate the area prior to starting the job. Acetone fumes are extremely flammable.
- Clean Up
Cured material should be removed mechanically or with an environmentally-safe solvent.
- Limitations
- This product is designed for professional use only.
- Apply in thin coats.
- Concrete must be free of sealers, wax, or curing agents.
- Be sure to paper off any areas that you do not want stained.
- Will not hide imperfections or stains in concrete.
- Fast stain will stain concrete and can produce a mottled look. Colors and effects will vary.
- Do not allow any westcoat products to freeze.
- Read product specification sheets for every product you will be using before beginning the project.
- Stains are translucent and somewhat transparent.
- For interior use only.
- Caution: when mixed with acetone, product is extremely flammable
Properties
- Typical Properties
- Mix Ratio
- 1 gal of Acetone per 1/2 Pint can
- 5 gal of Acetone per 1 Pint can
Value | Units | Test Method / Conditions | |
VOC Content | 0.0 | gm/l | - |
Safety & Health
- Health Precautions
- Inhalation of vapor or mist can cause headache, nausea irritation of nose, throat, and lungs.
- Prolonged or repeated skin contact can cause slight skin irritation.
- Be sure to extinguish all pilot lights and sources of ignition.
- Ventilate the area prior to starting the job.
- Acetone fumes are extremely flammable.
Packaging & Availability
- Packaging
- 1/2 Pint can (for 1 gallon of Acetone)
- 1 Pint can (for 5 gallons of Acetone)
Storage & Handling
- Shelf Life
5 years in unopened packaging