Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Primary Contents
Vinyl acetate homopolymer (CAS 9003207), Water (CAS 7732185), NJTSRN #950002 and #950003
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Product Highlights
- Glue spreader or spray application (glue spreader/pinch roller, glue spreader/hot press applications); suitable for postforming applications
- Professional use only
- Recommended as a sprayable version of Wilsonart 3000 for large panels
- High solids
- Does not require stirring before use
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Applications To Avoid
- Tempered hardboard products
- Fire retardant treated board products
- Boards treated to be moisture resistant
- Low pressure melamine surfaces
- Metallic, polyester and painted surfaces
- Liner grade laminate to plywood
- General Instructions
General Use Instructions
- Ensure substrates and adhesive are above 65°F.
- Best results are achieved between 70°F and 85°F.
- Surfaces must be clean and dry.
Hand Spray Instructions
- Fluid pressure: 30 psi; atomizing air pressure: 60 psi; fluid line: 3/8” I.D. minimum (See equipment recommendations later in this document).
- Coat both surfaces evenly with 7-8 wet grams/ft2 covering 100% of each surface. Coat each perimeter slightly heavier. Open time is 5 minutes. Bond immediately and before the adhesive film becomes more than 50% clear.
- Use mechanical pressure (pinch roller) on all assemblies greater than 4 ft2. Otherwise, apply 30-40 psi uniform downward pressure using hand-held J-roller over 100% of the bonded area.
- Large assemblies may be routed or filed immediately. Assemblies less than 4 ft2 should rest (5-10 minutes) prior to finishing. Use cover board to protect components against pulling, knocking or stress for one hour. Bond will usually reach full strength in 24 hours.
Spray Equipment Recommendations
- Binks: Gun: M95, M95 Auto, M61; Fluid Tip: 68ss (1-2 traversing heads), 66ss (3+ traversing heads), 66ss (edge/underwrap); Air Cap: 68PB (1-2 traversing heads), 66PJ (3+ traversing heads), 66R or 66PJ (edge/underwrap); Needle: 668 for 68ss fluid tip; 665 for 66ss fluid tip.
- DeVilbiss: Gun: JGA 510, MSA 510; Fluid Tip: D type; Air Cap: 64HD; Needle: D type
Flow-Through Postforming Instructions
- Coat both deck surfaces evenly with 7-8 wet grams / ft2 covering 100% of each surface. Coat board edge to be formed slightly heavier.
- Run laminate and core through drying oven that has been preset to achieve laminate exit temperature of 125°F-150°F. Adhesive film should appear dry (50% clear) but still soft to increased finger pressure.
- Index and apply uniform mechanical pressure (30–40 psi) while laminate temperature is at least 110°F.
- Postform per the manufacturer’s recommendations. 180° bends should end on a flat area at least 3⁄4” in width.
Glue Spreader/Hot Press Instructions
- Follow the glue spreader manufacturer’s recommendations
- .Use a dual durometer roller (Black Bros. A2158, 16 x 1⁄2” pattern).
- Select a groove pattern appropriate for PVA adhesive.
- Apply 6-8 wet mils with glue spreader.
- Open time is 5 minutes. Coating of only one surface is preferable.
- Assemble and hot press for 1-2 minutes under 40-50 psi and 180 ̊F-200 ̊F.
- Allow panel to cool for 2-5 minutes. Proceed with fabrication.
Properties
- Color
- Physical Properties
| Value | Units | Test Method / Conditions | |
| Viscosity | 2850.0 | cps | - |
| Density | 9.0 | lbs/gal | - |
| Solids Content | 56 - 60 | % | - |
| pH | 4 - 5 | - | - |
| Voc Content | max. 20 | grams/liter | Method 24 |
| Vhap Content | max. 0.032 | lbs/lbs solids | - |
| Coverage (7 Wet Mils) | approx. 229 | ft² /gallon | - |
| Coverage (Spray, Bonded) | approx. 255 | ft² /gallon | - |
| Hot Press Time (40 To 50Psi) | 1 - 2 | minutes | - |
| Open Time | 5.0 | minutes | - |
Regulatory & Compliance
- Certifications & Compliance
- Regulatory & Compliance
- GREENGUARD® Certified
- Complies with SCAQMD, Rule 1168
- Complies with the Ozone Transport Commission (OTC)
- Qualifies for LEED®-NC & CI EQ Credit 3.2: Construction Indoor Air Quality Management Plan-Before Occupancy
- Qualifies for LEED®-NC & CI EQ Credit 4.1: Low Emitting Materials: Adhesives & Sealants
- Qualifies for LEED®-NC & CI EQ Credit 4.4: Laminating adhesives shall contain no added urea-formaldehyde resins.
Safety & Health
- Safety
- Non-flammable
- Mildly irritating to eyes
- May irritate sensitive skin
- Inhalation may irritate respiratory tract
Packaging & Availability
- Packaging Type
- Availability
5-gallon pails, 55-gallon drums and 275-gallon totes (returnable)
Storage & Handling
- Storage
- Do not allow product to freeze.
- Close container tightly when not in use and store off the floor in a well ventilated area. Rotate stock.
- Shelf Life
Shelf life expires 1 year from manufacture date.
- Clean Up/Disposal
- Clean with hot tap water while adhesive is wet.
- Removal of dried adhesive is very difficult. Use diluted ammonia to clean dry adhesive.
- Wash water is RCRA non-hazardous.
- Dispose of in accordance with regulations.