Products in Fuel Systems: Plasticizer

WSD-800 is a colorless transparent oily liquid PVC plasticizer obtained from vegetable oil through catalytic hydrogenation, hydrolysis, dehydrogenation, distillation and esterification.

Paychlor D-45 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Epoxidized soybean oil/ESBO can be used in most products of polyvinyl chloride, such as all kinds of food package materials, medical products, different kinds of films, sheet materials, tubing, sealing strip of refrigerator, artificial leather, plastic wallpaper, electrical wires and cables and other commodity plastic products .It also can be used as special

Paychlor K-62 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Mediaplast PM is a synthetic aromatic plasticizer based on polyalkylbenzene (bi- and trialkylated aro-matics), which is mainly recommended for the use in elastomers with low to medium polarity, i. e. NR, IIR, BR, SBR, EP(D)M for example, but also CR, CM/CSM, EVA and PNR. Especially in polychloro-prene the often used, expensive ester plasticizers can be replaced completely.

Paychlor D-40 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Mediaplast NB-4 is a special adipine acid plasticizer at an exceptionally reasonable price for the use in polar polymers like NBR, H- and XNBR, CM / CSM, CR, ECO, etc. Mediaplast NB-4 is, due to its relatively low volatility and also because of its extremely low setting point, suitable for heat-resistant as well as cold flexible rubber articles (see technical data).

Plastay DINP (Di Isononyl Phthalate) is usually used with materials such as PVC for plasticization, after heating to a soft or plasticized state, to obtain elasticity, brightness for plastic, create electrical resistance, prevent cracking and make the surface smooth. Do not allow the ingress of materials that will be removed from the mold.

Mediaplast TR is a light, non-staining, highly aromatic synthetic plasticizer based on dibenzyltoluen.Due to these attributes it is recommended for the use in polar elastomers like CR, CM/CSM, NBR, HNBR etc. Mediaplast TR is especially suitable for the production of V-belts and special hoses (hy-draulic machinery, cars etc.) and other highly strained products.

Paychlor D-58 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor S-52 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor D-52 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor K-45 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

UPC Group DPHP has good compatibility with PVC, and its heat-resistance, cold-resistance, durability, migration-resistance, electrical property and volatility loss are better than DOP. DPHP has low-volatility properties and generates less fumes during processing, so it improves the durability of the product. Moreover, it is widely used in the cover and insulation of electric wires, and can also replace DIDP used for UL 70~90°C electric wire.

Paychlor S-45 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor D-42 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor S-58 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Mediaplast PS-1 is a synthetic plasticizer based on polyalkylbenzene, which is mainly recommended for the use in elastomers with low to medium polarity, e. g. NR, IIR, BR, SBR, EP(D)M, but also CR, CM/CSM, EVA and PNR.

Paychlor K-40 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor S-62 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor D-55 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Paychlor S-68 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Kettlitz-Mediaplast NB-7 is a special diisononyl dicarboxylic acid ester which can replace existing phthalate plasticizers in compounds based on polar rubbers like NBR, HNBR, CR, ACM, VAMAC etc. Mediaplast NB-7 shows minor volatility at an extremely low setting point. Therefore this plasticizer is suitable to produce rubber articles with high heat resistance and excellent low temperature propertiesas well.

Paychlor D-62 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Mediaplast PX-2 is a semi-synthetic plasticizer based on long-chain hydrocarbons with paraffinic character. It is recommended to use in elastomers with low polarity, e. g. NR, IIR, BR, SBR and EPDM.

Paychlor K-58 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Mediaplast 650 A is a synthetic plasticizer based on polyalkylbenzene (bi- and trialkylated aromatics), which is especially recommended for the use in elastomers with low polarity like NR, IIR, BR, SBR, EP(D)M, etc. The compatibility with rubber compounds containing strong polar elastomers, like nitrile rubber for example, is low.

Paychlor K-52 are used in blends with PAYAL’S PAYFLEX series to optimize cost, viscosity and processability. An extensive range of chlorinated paraffin grades are available ranging from chlorine content 0.36 to 0.65 and specific gravity 1.1 to 1.50.

Plastay D.O.P (Di Octyl Phthalate) is Generally used with materials like PVC in order to plasticized, after being heated to a doughy or plasticized state, to obtain elasticity, brightness for plastic material, generate electrical resistance, to prevent cracking and make surface smooth. Prevent materials which will be removed from mold from adhering to it.