Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Key Features
- Easy 10:1 mix ratio
- SA10-50A working time range from 25-65 min.
- SA10-100A working time range from 50-120 min.
- High viscosity for maximum gap filling.
- 2800 psi shear strength and up to 120% elongation.
- Little to no surface preparation.
- Primerless on most metals.
- Good chemical resistance
- Excellent fatigue characteristics and shock load resistance.
- Stable formulations with shelf-life of 6 months.
Applications & Uses
- Markets
- Compatible Substrates & Surfaces
- Substrates That Can Be Bonded
Wood, polyesters, vinyl esters, SMC, epoxies, acrylics, PVC/FPVC/CPVC, polycarbonate, ABS, styrenics, stainless steel, carbon steel, aluminum, coated metals, and many other composites, thermoplastics, and metals.
- Not Recommended For Bonding
Polyolefins: TPO’s, polyacetals, and PTFE
- Application Instructions
Automated equipment should be constructed of stainless steel. An exothermic chemical reaction occurs when components A and B are mixed and will generate heat. The amount of heat generated is relative to amount of mass of mixed product and also the working time of the Components A and B (or more relative to reactivity of product). Generally, faster curing products applied in larger beads or mixed left into large quantities can cause rapid boiling of monomers under excessive heat of reaction. These vapors are flammable or harmful if inhaled. Avoid sanding, grinding on cured adhesives (cut or scrape instead), which can produce noxious smoke that could contain harmful constituents, in this case consider a forced air breathing apparatus (PPE). After proper mixing of components, the VOC content of cured product will be less than 20 g/L (0.17 lbs./gal).
Use sufficient material to ensure the joint is completely filled when parts are mated and clamped. All adhesive application, part positioning, and fixturing should occur before the working time of the mix has expired. After indicated working time, parts must remain undisturbed until the fixture time is reached. The working time is the approximate time that the adhesive remains fluid and will still wet the surface of the adhered after mixing component A (adhesive) and component B (activator). The fixture time is the approximate time after mixing the two components that will allow the parts to be moved or unclamped. However, both working time and fixture times will increase or decrease depending on ambient temperatures and thickness of application. Thin applications in colder conditions can substantially increase fixture time. For applications in hot or cold ambient conditions, please contact your EBS representative. Clean-up is easiest before the adhesive has cured Citrus terpene or N-methylpyrolidone (NMP) containing, polar solvents, ketones. Avoid contaminating wet adhesive cosmetic surfaces with these cleaners, use masking tape and remove after applying while wet. If the adhesive is already cured, careful remove by scraping with a sharp tool, followed by a solvent wipe may be the most effective method of clean-up.- Directions
Surface Preparation:
The need for surface preparation must be determined by the user based on comparative testing of unprepared and prepared substrates to determine if strengths are adequate for application. Clean adhesive failure is not desired for long-term durable performance. In all cases initial shear strength tests must be followed up with simulated or actual durability tests to assure that surface conditions do not lead to degradation of the bond over time under service conditions. Subsequent changes in substrates or bonding conditions will require re-testing.
Most thermoplastics can be bonded with no surface preparation other than a dry wipe or air blow-off. If contamination is visible or suspected, wipe with alcohol prior to bonding. Low surface energy plastics like polyolefins, thermoplastic polyesters and fluorocarbon plastics are generally not bondable.
Metals:EBS recommends surface preparation of most bare metals prior to bonding with ACRALOCK adhesives. Preparation of metals may involve sanding, solvent wipe, solvent immersion or dry wipe. After cleaning, EBS recommends a final wipe of all bondable surfaces using ACRALOCK AP-1, an alcohol based cleaner/primer, to achieve better adhesion, and long-term bond durability. Metal to metal assemblies with thin bond gaps ≤ .015” requires standoff or spacers for uniformity. Metals such as cold rolled steel, carbon steel, ductile iron, etc. require sanding to remove rust, oxidation or scale followed by cleaning with AP-1 cleaner/primer. High strength galvanized steel should be sanded, cleaned with AP-1 and tested with 1:1 ACRALOCK products, such as SA1-05A or SA1-700A, for best results. Surface preparation, and AP-1 wipe is strongly recommended for best adhesion. Powder coated and painted metals do not require AP-1, but should be tested before bonding. All other metals should be tested prior to bonding.
Thermoset composites are generally bonded without preparation; however, mold releases and process can produce varied bonding performance and testing should be performed.
Elevated temperature cohesive strength at 180°F retains a minimum of 500 psi as measured on aluminum. Bonds can be exposed to intermittent temperatures up to 250°F, provided at the higher temperature range bonding assembly is in a fixture and not under shear load. User must determine suitability for all applications and operating conditions.
Chemical Resistance:EBS strongly recommends laboratory and end-use testing representative of the environmental conditions and how the bonded assembly will be used. Bonds are generally resistant to the effects of heat, water and moisture, aqueous chemicals and some intermittent exposure of gasoline, motor oil and diesel fuel. Not recommended for immersion or long-term exposure to all hydrocarbons, concentrated acids or bases, or aggressive organic solvents such as toluene, ketones, and esters.
Properties
- Cured Properties
| Value | Units | Test Method / Conditions | |
| Tensile Strength | 2,500 - 3,000 | psi | — |
| Modulus | 60 - 90 | kpsi | — |
| Elongation | 80 - 120 | % | — |
| Lap Shear Aluminum | 2,300 - 2,800 | psi | ASTM D1002 |
| Lap Shear Stainless Steel | 2,300 - 2,800 | psi | D1002 |
| Lap Shear Cold Rolled Steel | 2,200 - 2,700 | psi | D1002 |
| Lap Shear Pultrusion-FRP | 2,400 - 2,900 | psi | D5868 |
Technical Details & Test Data
- Temperature Exposure
Temperature range for this product is from -40 to 180 °F (-40 to 82 °C) with intermittent exposure between -67 to 250°F ( -55 to 121 °C).
- Typical Adhesive Wet Properties
Property Comp A Comp B Mixed Color OWT BLK/GRY BLK/GRY Viscosity (cP) 800K-1,200K 100K-200K - Mix ratio weight 9.4 1 - Mix ratio volume 10 part 1 part - Density g/cc 1.015 1..079 - WPG lb/gal 8.47 8.95 - Activator is available in OWT (Density 10.6 LB/GAL). Mix ratio by weight is 8:1.
- Cartridge Code-Working Time
ACTIVATOR→ ACT-3B BLK, GRY ACT-4B BLK, GRY ADHESIVE↓ SA10-50A SA10-75 SA10-100 Working time (min) 65-90 90-120
Packaging & Availability
- Packaging Type
- Packaging
ACRALOCK adhesives, manufactured by Engineered Bonding Solutions, LLC., are packaged in 490mL dual cartridges as well as 5- and 50-gallon containers for application with meter-mix dispensing equipment.
Storage & Handling
- Shelf Life
The shelf life of Components A and B in unopened containers is determined from the date the product is manufactured at EBS facilities. Shelf life is based on steady state storage between 55°F and 80°F (13°C and 27°C). Exposure, intermittent or prolonged, above 80°F/27°C will result in a reduction of the stated shelf life. Shelf life of both components can be extended by air-conditioned or refrigerated storage between 55°F and 65°F (13°C and 18°C). Refer to Product Label for Product expiration date.