Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Type
- 100% Silicone
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- Neutral cure formulation, ideal for use in corrosion-sensitive electronic equipment with no adverse effects.
- Will not corrode copper, brass or silver.
- Effectively fills small spaces and is easy to rework and repair.
Applications & Uses
- Markets
- Cure Method
- Typical Uses
- Flowable and self-leveling applications
- Fills small places
- Potting electrical terminals
- Sealing electronic devices
- Drying Time
Skin-Over Time 2-10 minutes Cure Time 24 hours Full Physical Characteristics 7 days - Surface Preparation
All surfaces should be clean and dry, and free of dust, dirt, and grease. It is recommended that bonding surfaces be wiped with an oil-free solvent. Allow surface to dry thoroughly before applying sealant.
Priming is normally not required for applications to most substrates. Applying a small trial bead and allowing 7 days for maximum adhesion to occur can readily test unprimed adhesion.
- Application
CSL507 is ready to use and requires no mixing or additives. The cure mechanism begins as soon as the sealant is exposed to air. The uncured sealant will flow until a cured skin is formed. At conditions of 25°C (77°F) and 50% relative humidity, a bead of sealant 3mm (1/8”) will skin over in 2-10 minutes and fully cure in 24 hours. Higher humidity accelerates cure. In applications where partial or total confinement of sealant is prevalent, the time required for proper cure is generally lengthened by the degree of confinement.
In confined cure conditions, CSL507 neutral cure sealant may discolor brass, copper, or other sensitive metals, and/or stress craze polycarbonate.
CSL507 should not be applied below grade, to surfaces under continuous water immersion, to substrates that bleed oils, plasticizers or solvents (e.g. impregnated wood, oil-based caulks, green or partially vulcanized rubber gaskets or tapes), to surfaces in direct contact with food, and to surfaces that will be painted over.
Properties
- Color
- Physical Form
- Appearance
- Smooth, Thick Liquid
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Specific Gravity (Uncured) | 1.02 | - | - |
| Slump/Sag (Uncured) | Flowable | - | - |
| Extrusion Rate (Uncured, 3.2mm Orifice, 90psi) | 100.0 | g/min | - |
| Cure System (Uncured) | Neutral (Oxime), Moisture Cure | - | - |
| Hardness (Cured At Standard Conditions* for 7 Days) | 25.0 | Shore A | ASTM D2240 (Durometer) |
| Tensile Strength (Cured At Standard Conditions* for 7 Days) | 300.0 | psi | ASTM D412 |
| Elongation at Break (Cured At Standard Conditions* for 7 Days) | 400.0 | % | ASTM D412 |
| Tear Resistance (Cured At Standard Conditions* for 7 Days) | 25.0 | ppi | ASTM D624, Die B |
| Dielectric Strength (Cured At Standard Conditions* for 7 Days) | 733.5 | V/mil | ASTM D149 |
| Dielectric Constant (100Hz, Cured At Standard Conditions* for 7 Days) | 4.13 | - | ASTM D150 |
| Dielectric Constant (100kHz, Cured At Standard Conditions* for 7 Days) | 4.17 | - | ASTM D150 |
| Volume Resistivity (Cured At Standard Conditions* for 7 Days) | min. 1.4 × 10¹² | ohms.cm | ASTM D257 |
| Dissipation Factor (100Hz, Cured At Standard Conditions* for 7 Days) | 0.86 | - | ASTM D150 |
| Dissipation Factor (100kHz, Cured At Standard Conditions* for 7 Days) | 0.737 | - | ASTM D150 |
| Value | Units | Test Method / Conditions | |
| Application Temperature Range (Ambient) | 120.0 | °F | - |
| Useable Temperature Range | -76 to 392 | °F | - |
Regulatory & Compliance
Safety & Health
- Safety Precautions
CSL507 uses a neutral cure system, so no acetic acid or objectionable by-products are evolved during the cure. Adequate ventilation should be provided with extensive use of this sealant.
On direct contact, the uncured sealant may irritate the eyes. Flush well with water and call a physician. Avoid prolonged contact with skin. See the Safety Data Sheet available on this product.
All work involving the application and use of this product should be performed in compliance with all relevant national, Health, Safety & Environmental standards & regulations.
Packaging & Availability
- Packaging Type
- Packaging
CSL507 is available in 300mL (10.2 fl. oz.) cartridges, 19L (5 US gallon) pails and 189L (50 US gallon) drums.
Storage & Handling
- Storage
CSL507, when stored in original, unopened container in dry, shaded conditions, away from sources of heat or ignition, and stored at or below 32°C (90°F), has a shelf life of 12 months from date of manufacture.