Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Product Families
- Composition
Polyamide-modified epoxy resin and wetting agents.
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- The moisture tolerance of Perdure E02 allows it to be applied to damp concrete after surface preparation.
- This includes bonding “old to old” or “new to old” concrete.
- Low modulus - stress relieving.
- Fast cure formulation available for priming undercoatings.
- Moisture insensitive cure.
- Conforms to ASTM C-881 requirements.
- Low viscosity-good wetting properties.
Applications & Uses
- Markets
- Substrate Requirements
- Bonding surfaces must be sound, clean, and free from standing water.
- Substrate temperature must be a minimum of 50°F.
- The substrate must be free of dirt, waxes, curing agents and other foreign materials.
- Perdure E02 should not be installed on new concrete until maximum shrinkage has occurred (at least thirty days after pour).
- Applications
- Surface preparation is the most critical portion of any successful resinous flooring system application.
- All substrates must be properly prepared as outlined in Düraamen’s Technical Bulletin # 1.
- Work must be performed by trained or experienced contractors or maintenance personnel.
- Installation
- When priming, spread Perdure E02 at a rate of 250 - 275 ft² per gallon.
- Care should be taken to avoid puddles.
- The application can be made with a brush, roller, or squeegee.
- For mortar applications, allow Perdure E02 to set for 30 minutes before topping.
- After seven (7) hours, it will be too hard.
- Coating applications should not be recoated until Perdure E02 is completely cured.
- To speed up the application process, use a fast cure formulation.
- For complete installation instructions, contact your Düraamen representative.
- Clean Up
- Clean skin with soap and water.
- Tools and equipment should be cleaned with Xylene or Lacquer Thinner.
- Coverage
100 to 180 sq. ft. per gallon depending upon the application method and porosity of the substrate.
- Maintenance
- After completing the application of Perdure E02, the installer should provide the owner with maintenance instructions.
- If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.
- Perdure E02 is easily cleaned with neutral soaps or detergents.
- Routine mechanical scrubbing is recommended for all surfaces having a non-skid texture.
- Waxing is optional.
- Long periods of heavy traffic may cause wear patterns necessitating the application of a finish coat.
Properties
- Color
- Component A
- Component B
- Technical Data
| Value | Units | Test Method / Conditions | |
| Mixing Ratio by Volume | 2.0 | — | — |
| Value | Units | Test Method / Conditions | |
| Mixing Ratio by Volume | 1.0 | — | — |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (75°F) | 6 - 8 | hours | — |
| Full Cure (max. Resistance) | 5 | days | — |
| Gloss (70°F) | Low Sheen | — | — |
| Re-coat (Fast Cure, 75°F) | 4 - 6 | hours | — |
| Re-coat (Regular Cure, 75°F) | 10 - 12 | hours | — |
| Solids Content by Volume | 100.0 | % | — |
| Viscosity (70°F) | 400 - 450 | cps | — |
| Weight Per Gallon (Mixed) | 9 - 9.5 | pounds per gallon | — |
Packaging & Availability
- Color Selection
- Perdure E02 is available in Clear or Standard Colors.
- Custom colors are available subject to laboratory approval, minimum quantity, lead time for production, and increased cost.
- Packaging
- 1.5-gal
- 3-gal
- 15-gal
Storage & Handling
- Pot Life
- 30 - 40 minutes