Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Composition
100% solids amine cured epoxy resin.
Features & Benefits
- Ready-to-Use Product Features
- Advantages
- Good troweling properties when used with Duraamen self-leveling epoxy mortar and quartz systems.
- Excellent color retention when used as a topcoat with Düraamen flooring systems.
- Good trowelling properties when used in mortar systems.
- Low odor for use in occupied areas.
- Available in fast cure systems.
Applications & Uses
- Markets
- Application Method
- Substrate Requirements
- Bonding surfaces must be sound, clean, and free from standing water.
- Substrate temperature must be a minimum of 50°F.
- The substrate must be free of dirt, waxes, curing agents and other foreign materials.
- Pigmented version should not be used as a topcoat.
- Applications
- Surface Preparation is the most critical portion of any successful resinous flooring system application.
- All substrates must be properly prepared as outlined in Düraamen Technical Bulletin # 1.
- Work must be performed by trained or experienced contractors or maintenance personnel.
- Clean Up
- Clean skin with soap and water.
- Tools and equipment should be cleaned with Xylene or Lacquer thinner.
- Coverage
80 - 160 sq. ft. per gallon depending upon the application method and porosity of the substrate.
- Maintenance
- After completing the application of Perdure E10, the installer should provide the owner with maintenance instructions.
- If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.
- Perdure E10 is easily cleaned with neutral soaps or detergents.
- Routine mechanical scrubbing is recommended for all surfaces having a non-skid texture.
- Waxing is optional.
- Long periods of heavy traffic may cause wear patterns necessitating the application of a finish coat.
Properties
- Color
- Component A
- Component B
- Technical Data
- Performance Properties
| Value | Units | Test Method / Conditions | |
| Mixing Ratio by Volume | 4.0 | — | — |
| Value | Units | Test Method / Conditions | |
| Mixing Ratio by Volume | 1.0 | — | — |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (75°F) | 6 - 8 | hours | — |
| Full Cure (max. Resistance) | 5 | days | — |
| Gloss (600°F) | 85 - 100 | — | — |
| Re-coat (Fast Cure, 75°F) | 4 - 6 | hours | — |
| Re-coat (Regular Cure, 75°F) | 10 - 12 | hours | — |
| Solids Content by Volume | 100.0 | % | — |
| Viscosity (75°F) | 950.0 | cps | — |
| Weight Per Gallon (Mixed) | 9 - 9.5 | pounds per gallon | — |
| Value | Units | Test Method / Conditions | |
| Abrasion Resistance (CS-17 Wheel, 1kg Load, 1000Loads) | 35 - 40 | mg Loss | ASTM C501 |
| Adhesion to Concrete (Concrete Fails) | 350.0 | psi | ACI403 |
| Adhesion to Metal | 2500.0 | psi | — |
| Compressive Strength | 11000.0 | psi | ASTM D 695 |
| Elongation | 5.5 | % | ASTM D638 |
| Flexural Strength | 8000.0 | psi | ASTM D790 |
| Hardness | 80.0 | Shore D | ASTM D2240 |
| Impact Resistance (No Cracking, Delamination or Chipping) | 16.0 | ft.Ib. | MILD 3134F |
| Indentation (Withstands for 30min Without Indentation) | 2000.0 | lb/sq.in | MILD 3134F |
| Service Temperature (Dry Heat) | 185.0 | °F | MILD 3134F |
| Service Temperature (Immersion) | 160.0 | °F | MILD 3134F |
| Tensile Strength | 8500.0 | psi | ASTM D638 |
| Water Absorption (24hr Immersion) | max. 0.1 | % | ASTM D 67063 |
Regulatory & Compliance
- Certifications & Compliance
- Regulatory & Compliance
- USDA approved for food handling applications.
Technical Details & Test Data
- Chemical Resistance
Reagent Rating Acetic Acid-5% Limited Use, Occasional Spills Acetone Limited Use, Occasional Spills Bleach Limited Use, Occasional Spills Citirc Acid-30% Recommended for Continuous Service Crude Oil Recommended for Continuous Service Diesel Fuel Recommended for Continuous Service Ethylene Glycol Recommended for Continuous Service Fatty Acids Limited Use, Occasional Spills Gasoline Recommended for Continuous Service Hydrochloric Acid-15% Recommended for Continuous Service Lactic Acid-15% Recommended for Continuous Service MEK Limited Use, Occasional Spills Nitric Acid-10% Recommended for Continuous Service Skydrol Recommended for Continuous Service NaOH-50% Recommended for Continuous Service Sulfuric Acid-20% Recommended for Continuous Service Toluene Recommended for Continuous Service Urea Recommended for Continuous Service Vinegar Limited Use, Occasional Spills Xylene Recommended for Continuous Service
Packaging & Availability
- Packaging
- 1.25-gal
- 5-gal
- 25-gal
Storage & Handling
- Pot Life
- 30 - 40 minutes