Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Limitations
- Always determine suitability by applying a test area.
- When adding to Urethane products, gloss and slip resistance should be evaluated to determine suitability. Contact the manufacturer for application details. After adding to the Urethane product, occasionally re-stir to insure a homogenous mixture and uniform application appearance.
- Slab on grade requires moisture barrier.
- Substrate temperature must be 5°F above dew point. All new concrete must be cured for at least 30 days.
- Colors may vary from batch to batch.
- Mix Ratio
Broadcast 3.5 lbs on average to cover up to 500 sq.ft.
- Mixing & Application Instructions
Product Storage: Store product in an area so as to bring the material to normal room temperature before using. Keep material dry.
Surface Preparation: Surface preparation will vary according to the type of complete system to be applied. For a one or two coat thin build system (3 - 10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign contaminants, and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4' x 4' plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding.
Product Mixing: The liquid portion of the product selected for use is first thoroughly mixed at the correct mix ratio. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After the liquids are mixed, add in the correct amount of aggregate. Avoid whipping air into the coating. Improper mixing may result in product failure.
Product Application: See individual technical data sheets for specific application procedures. Stir the mixed material occasionally to prevent the settling out of the added aggregate. Maintain temperatures within the recommended ranges during the application and curing process. Too thick of an application may result in solvent entrapment and product failure or gloss inconsistencies.
Recoat or Topcoating: See individual Product technical data sheets for recoat or topcoating application information.
Cleanup: Refer to individual Technical data sheets for information.
Floor Cleaning: Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.
Restrictions: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see individual technical data sheets under full cure). It is best to let the floor remain dry for the full cure cycle.
- Recommended For
With products 100% Solids Epoxy EP600 and EP500 line of products.
Note: EP500 Metallics Epoxy will have a reduced sheen when using this broadcast.
Properties
- Color
- Typical Properties
- Chemical Composition
| Value | Units | Test Method / Conditions | |
| Apparent Porosity | 3 - 5 | % | - |
| Bulk Specific Gravity (Typical, True Density of 3.9 - 4.0) | 3.5 - 3.6 | - | - |
| Hardness (Mohs) | 9.0 | - | - |
| Melting Temperature | min. 2000 | °C | - |
| Refractive Index | 1.70 - 1.80 | - | - |
| Solids By Weight | 100.0 | % | - |
| Volatile Organic Content | 0.0 | pounds per gallon | - |
| Water Absorption | approx. 1 | % | - |
| Value | Units | Test Method / Conditions | |
| Alpha Phase | min. 99 | % | - |
| Aluminium Oxide | min. 95 | % | - |
| Iron (III) Oxide | max. 10 | % | - |
| L.O.I (300 - 12000°C) | 0.0 | - | - |
| Silicon Dioxide | max. 0.05 | % | - |
| Sodium Oxide | max. 0.30 | % | - |
Packaging & Availability
- Packaging Information
Packaging size varies from a pint to a 5 gallon pail. Normal pint packaging weight is 1.6 pounds.
Storage & Handling
- Shelf Life
- Indefinite