Products

Diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide is a Type I photoinitiator best known for it's through cure abilities. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7210 has a unique combination of high tensile strength and good elongation, which results in excellent toughness upon curing. PL-7210 is also very low color.

2-Methyl-1-[4-(methylthio) phenyl]-2-morpholino propan-1-one is a type I photoinitiator primarily used in pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7110 is a low color urethane that is a viscous liquid at room temperature. Upon cure, PL-7110 creates a tough polymer with percent elongation near 60%. PL-7110 is non-yellowing and can be used in formulations to add toughness.

PL-7113 is a non-yellowing urethane that exhibits a high degree of elongation. It also has a high rate of conversion with low average shrinkage stress. PL-7113 can be added to formulations to add toughness.

PL-7021 has a unique structure which results in a flexible cured product. Adding PL-7021 to formulations has been shown to increase toughness.

PL-3208 Ethoxylated Bisphenol A Dimathacrylate is a difunctional monomer providing low volatility and flexibility.

4-phenyl benzophenone is a very fast curing type-II photoinitiator. In the presence of O2, the use of an amine co-initiator is recommended. It is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

2-hydroxy-2-methyl-1-phenyl-1-propanone is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-4265 is a 50:50 liquid blend of 2-hydroxy-2-methyl-1-phenyl-1-propanone and diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide. It provides exceptional cure response in white and pastel pigmented systems as well as thicker clear films. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. PL-4265 soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-7002 is a tetrafunctional polymethacrylate. This increased functionality results in faster cure speeds due to increased cross-linking capacity. Upon curing, PL-7002 exhibits very high Shore D hardness values. PL-7002 is non-yellowing and can be used in formulations to add strength.

PL-7130 is a low color urethane that is a viscous liquid at room temperature. Upon cure, PL-7130 creates a flexible yet tough polymer with percent elongation near 80%. PL-7130 is non-yellowing and can be used in formulations to add flexibility.

PL-7003 is a low viscosity urethane that exhibits very fast cure speeds. Upon curing, PL-7003 exhibits excellent hardness and very low color. PL-7003 can be used in formulations to add strength.

PL-3216A is a difunctional monomer providing water resistance and fast cure.

PL-3116 is a monofunctional monomer providing good adhesion, high Tg, and low viscosity.

PL-3203 is a difunctional monomer providing good flexibility and is water soluble.

2-Benzyl-2-dimethylamino-1-(4-morpholinphenyl) butanone is a type I photoinitiator primarily used in non-white pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3216 is a difunctional monomer providing water resistance and fast cure.

PL-7000 is a low viscosity urethane dimethacrylate. When cured, PL-7000 exhibits good hardness and strength. PL-7000 is low in color.

PL-3220 is a difunctional monomer providing a good balance of hydrophobicity and hydrophilicity.

PL-7121 is a novel low-shrink urethane monomer based on Esstech's proprietary methacrylate technology. PL-7121 possesses a volumetric shrinkage of 2.0 - 2.5% and conversion of 65 - 80% without filler. PL-7121 has very low color and can be added to formulations to add toughness. PL-7121 possess the excellent combination of superior elongation and strength.

1-hydroxy-cyclohexylphenyl-ketone is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3216B is a difunctional monomer providing water resistance and fast cure.

PL-3110 is a monofunctional monomer providing good adhesion and low viscosity.

PL-3214C is a difunctional reactive monomer that provides excellent diluecy as well as water resist. and weathering prop.

PL-3100 is a monofunctional monomer with excellent hardness properties.

PL-7011 exhibits excellent flexibility upon curing. It is a non-yellowing extended urethane dimethacrylate and can be used in formulations to add toughness.

PL-3204 is a difunctional monomer providing flexibility and hydrophobicity.

PL-CLR is a liquid photoinitiator compound developed specifically for thicker clear films where low yellowing is necessary. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. Because it’s a liquid, it works well as a press side additive for the printer. PL-CLR is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3103 is a monofunctional monomer that provides good adhesion and low shrinkage.

4-Methyl benzophenone is a fast curing type-II photoinitiator. In the presence of O2, the use of an amine co-initiator is recommended. It is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-500 is a eutectic blend made up of a 1:1 mixture of PL-CPK and PL-BPO. It is well suited for applications where ease of use and good surface cure are needed. PL-500 is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

2-Isopropylthioxanthone is a Type II photoinitiator. It is typically used in combination with tertiary amines. Another major use is as a sensitizer to enhance the curing efficiency of both PL-907 and PL-369. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-600 is a liquid Photoinitiator compound developed specifically for white and pastel pigmented systems as well as thicker clear films. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. Because it's a liquid, it works well as a press side additive for the printer. PL-600 is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3214B is a difunctional reactive monomer that provides excellent diluecy as well as water resist. and weathering prop.

PL-3102 is a monofuctional monomer that provides water resistance and flexibility.