Products

GEHR ABS® is amorphous material belongs to the polymer group of standard plastics, due to its thermal and mechanical properties. The material has a high surface hardness, but is not UV-stable. ABS is suitable for galvanized components.

GEHR E-CTFE® is a linear block copolymer and belongs to the group of amorphous high-performance plastics. It is highly UV and weather resistant and also withstands high-energy (radioactive) radiation. Ethylen-Chlortrifluorethylene exhibits an extraordinary impact strength at temperatures ranging from -76 °C to +150 °C. A great part of the product properties attributes to the very smooth surface and differentiates HALAR® from other fluoropolymers. Due to the fact that E-CTFE is very pure, this material is being used to process chemicals and ultrapure water for the semiconductor industry. Also the permeation resistance to oxygen, carbon dioxide, chlorine gas and hydrochlorid acid is 10 to 100 times better than PTFE.

GEHR POM® C 25GF has a broad property profile that offers increased strength for many applications compared to non-reinforced GEHR POM-C®. In addition, the reinforcement reduces the coefficient of expansion and simultaneously increases the heat deflection temperature.

GEHR POM® ELS is a variant of POM-C with enhanced electrical conductivity. The conductivity is generated by a specially adjusted additive. Migration to the part surface, and thus strong fluctuation of the good conductivity, should therefore not occur. The surface resistance, measured on the semi-finished product, is ≤104 Ω.

GEHR PEEK® 20 TF (GLIDE) is made in response to enquiries for a material with the properties of natural-colored PEEK but with optimized sliding properties. Although PTFE additives in plastics often lead to a fibrous surface, we were able to achieve an almost shiny surface during processing. This material was developed to optimize the performance of PEEK in friction and wear applications by offering improved lubricity and reduced friction compared to standard PEEK. It offers all the standard advantages associated with standard PEEK resins, such as high mechanical strength and rigidity, excellent thermal oxidative stability, fatigue resistance and excellent resistance to tough chemical environments. Here, it offers clear advantages over the materials PEK, PEKK or PEKEKK.

GEHR PA® 6 XT is a PA 6 which shows a very tough behavior and which was produced by extrusion. Our round rods and sheets in natural color comply with the food contact regulations according to 10/2011/EC.

GEHR PA® 6.6 is slightly increased surface hardness and rigidity of PA 6.6 is due to the reduced moisture absorption behavior compared to PA 6 XT. Abrasion resistance and heat deflection temperature could also be optimized at the expense of toughness.

GEHR PVDF® shows a higher tensile strength, pressure resistance and dimensional stability than the related PTFE, but friction and insulation properties are lower. PVDF has a high mechanical strength and toughness at lower temperature and it’s self-extinguishing. The operating temperature ranges from -30 °C to +150 °C. PVDF shows a high resistance to chlorine, bromine and high-energy radiation.

GEHR PSU® is amber-colored, transparent material belongs to the group of amorphous high-performance plastics. Polysulfone has a good heat deflection temperature and heat aging resistance (-100 °C to +160 °C). In addition, this material has a high hardness and strength, very good hydrolytic stability and high radiation resistance (permeable to microwaves up to 2.45 GHz). PSU also has high dimensional stability and resistance to β- and γ-, X-rays and infrared rays. However, PSU is not UV stable and notch sensitive.

GEHR POM® C is produced from the continuous operating temperature of this engineering plastic ranges between -40 °C and +100 °C. Based on its toughness combined with high dimensional stability, there is no tendency to stress cracking. The copolymer has high thermal stability and chemical resistance. In particular, the increased hydrolytic stability and resistance to contact with many solvents must be taken into account. This material is frequently found in applications in the food industry, as cleaning processes require resistance to the use of hot water or various chemical agents. Our round rods and sheets in natural or black color comply with the food contact regulations according to 10/2011/EC.

GEHR POM® ESD 9 is a variant of POM-C with reduced surface resistance. Unfilled thermoplastic materials made of plastic are electrically insulating and are classified as non-conductors. By means of certain modifiers, such as treated carbon black, metal fibers or certain salts, however, an inherently acting electrical conductivity can also be introduced. This can result in antistatic, static dissipative or even very conductive properties. The aggregates used are not subject to migration, so that continuity of this special property is ensured. In our standard program we have the following electrically conductive materials in stock: GEHR PE-ELS®, GEHR POM-ELS® and GEHR PVDF-ELS®. Due to market-specific requirements, we have now added an electrically conductive type to the technical materials: GEHR POM-ESD 9® has a static conductivity with a surface resistance of between 106 Ω and 109 Ω. This favors applications in sensitive electrical engineering and conveyor technology with – at the same time – increased requirements in explosion protection.

GEHR PBT® is a semi-crystalline material from the polyester family of plastics and, due to its good thermal and mechanical properties, is counted among the polymer group of engineering plastics. It has a high surface hardness and good sliding and wear behavior.

GEHR PEI® has a high mechanical strength in connection with a good chemical and heat resistance (operating temperature up to +170 °C), good dimensional stability and creep resistance. lts unique torque strength permits the economical substitution of machined fabricated small parts from steel.

FIL-A-GEHR® PEEK MG (MEDI) is a high performance filament based on the material PEEK and is suitable for medical and pharmaceutical applications in direct body contact with tissue, bone, skin and mucous membrane up to 24 hours. They have been tested and evaluated by independent, accredited test laboratories and meet the following biocompatibility requirements: – ISO 10993-1/5/12/18 and USP Class VI.

GEHR PA® 6 C is a high-molecular and stress-reduced PA 6, which shows a very tough behavior and which was produced by casting. Our round rods and sheets in natural color comply with the food contact regulations according to 10/2011/EC.

GEHR PET® is a semi-crystalline material from the polyester family of plastics and, due to its good thermal and mechanical properties, is counted among the polymer group of engineering plastics. It has a high surface hardness and good sliding and wear behavior.

GEHR PEEK® can be used at very high temperatures (about +260 °C) and it shows an extraordinary mechanical strength, toughness, hardness, flexural strength, torsional strength. PEEK exhibits excellent chemical resistance, very good dielectric properties up to +260 °C and a very good resistance to all kinds of radiation (even ultraviolet rays only lead to a slight yellow discolouration). PEEK is self-extinguishing properties according to UL 94.

GEHR PPSU® is an amorphous material, with improved impact and hydrolysis resistance compared to PSU. This amber-colored, transparent material is usually used in a black color, which is why we only offer it in this color version so far. The usual operating temperature is approx. +170 °C. The extremely high notch impact strength remains also after a heat aging.

GEHR PPS® is continuous operating temperature of this high-performance plastic is approximately +230 °C. It has very high mechanical performance combined with excellent thermal and chemical resistance as well as high dimensional stability and creep resistance. The LOI of this material is among the highest among polymers. The excellent hardness and stiffness are further characteristics of PPS. It closes the gap between semi-crystalline, engineering plastics and PEEK through its strength and economic efficiency.

GEHR PA® 6.10 (ECO) is a semi-crystalline material obtained from the oil of the castor seed. The proportion of renewable raw materials here is over 60 %. The water absorption of PA 6.10 is lower than that of the related and oil-based PA 6, which results in increased dimensional stability.

GEHR PMMA XT® (ACRYL) is amorphous material belongs to the polymer group of standard plastics, due to its thermal and mechanical properties. In addition to its high mechanical strength and rigidity, it certainly has an extraordinarily brilliant transparency. Its weather and UV resistance as well as its surface hardness are also very high. PMMA is also scratch-resistant and polishable. The continuous operating temperature ranges between -40 °C and +70 °C. The chemical resistance to most solvents, the resistance to stress cracking as well as the toughness is clearly subordinate compared to other materials from the group of standard polymers.

GEHR PEEK® 30CF is a variant of PEEK modified with 30 % carbon fibers. As with the glass-fiber reinforced type, the surface hardness and heat deflection temperature are also significantly increased compared to the already high values of the unreinforced standard type. This material owes its significantly increased dimensional stability to its extremely low coefficient of linear expansion. The electrical properties are influenced by the high proportion of carbon fibers and must be taken into account in the relevant applications.

GEHR PEEK® HT is one of our contributions to innovation is to extrude the new SOLVAY PEEK-HT material, which may be used in particular in the chemical industry. With PEEK-HT, Solvay developed a new material which has a glass transition temperature (170 °C) and heat deflection temperature (HDT/A=175 °C) that are both approx. 20 °C higher that those of PEEK, without losing its high chemical resistance. This is usually the case with the materials from the same material family, such as PEK, PEKK or PEKEKK. The melting point of PEEK-HT is approx. 385 °C. At the same time, it was possible to significantly increase the dielectric strength from 16 to 23 kV/mm. The raw material manufacturer now specifies a compressive strength of 160 MPa compared to the former value of 118 MPa. The notched impact strength, measured according to ASTM D256, is also specified with an increased value of 106 J/m compared to 91 J/m for standard PEEK.

GEHR PEEK® MOD (GLIDE) is reinforced with 10 % of each PTFE, graphite and carbonfibre. The very good friction, wear and tear properties makes this material the good choice for many applications with friction.

GEHR PE-ELS® is a variant of PE-HS with improved electrical conductivity. By means of a special conductive carbon black, the volume resistance could be reduced to ≤104 Ω and the surface resistance to ≤105 Ω.