Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- Low VOC, single component.
- Excellent caulking and spraying properties.
- Silicone, halogen, asbestos and solvent-free.
- Excellent airborne sound insulation.
- Smoke and fume resistant.
- Easy clean up with water.
- Low volume shrinkage.
- Paintable.
- Available in caulking and sprayable grades.
Applications & Uses
- Markets
- Applications
- Applications
- Reducing the transmission of sound through wall openings.
- Stopping the passage of smoke in smoke barrier walls.
- Stopping air leakage to reduce the passage of dust and airborne infectious particles.
- Installation Guide (Caulking Type)
- Application substrate should be cleaned of loose debris, dirt, oil, wax, grease and other contaminants the surface must be moisture and frost-free.
- Install backing material as needed.
- The depth of the joint should be 1/4" (6 mm) minimum to 3/8" (9 mm) maximum.
- Sealant can be applied with standard or bulk caulking guns, manual trowel or spray application.
- Apply sealant in opening and work into all areas eliminating voids or seams and making complete contact with substrate.
- Spraying Guide (Spray Type)
- Mix INSS0285 SPRAY thoroughly using a power agitator before application.
- Thinning is normally not required, if necessary, use potable water (3% max.) to adjust viscosity.
- Apply via airless spray equipment in a single pass not more than 1mm WFT to prevent sagging.
- Recommended sprayer: Model: Graco 1095 (3300psi) Filter in the machine: 60 mesh Filter in spray gun: 100 mesh Tip: 517 - 523.
- Recommended application temperature shall be between 5 - 40 °C.
- Do not allow the sealant material to remain in hoses, guns or spray equipment when not in use.
- Clean all equipment with water immediately after use.
- All unused sealants should be stored in a tightly closed container.
- Surface skinning may occur in a partially filled container in which case filter the material before use.
- Wet film thickness approx.1mm cures to 0.64mm dry film.
- Thickness measurement - wet film thickness of the sealant layer can be measured using a wet film thickness gage.
- The dry film thickness can be verified using calipers or micrometers.
- Limitations
- Not for use in areas immersed in water.
- The sealant can only be removed mechanically once cured.
- This product is not intended for use in fire-rated construction.
- Uses
- Joint systems
- Dry wall
- Curing Time
3mm/3days (at 25°C/ RH50%)
- Types of Applications
- Joint systems
- Partition wall
Properties
- Specifications
- Typical Thickness Temperature
1mm at WFT = 0.7mm DFT
| Value | Units | Test Method / Conditions | |
| Density | 1.5 - 1.7 | g/cm³ | — |
| Skin-Forming Time | approx. 25 | minutes | — |
| Elongation at Break | 300.0 | % | — |
| Application Temperature | 40 - 104 | °F | — |
| In-Service Temperature | -13 to 176 | °F | — |
| Mold and Mildew | Mold Resistant | — | ASTM G21 |
| Volume Shrinkage (Class 0) | 22.3 | % | ASTM C1241 |
| VOC | 42.0 | g/L | — |
| Surface Burning Characteristics (Smoke Development) | 5.0 | — | UL 723 (ASTM E84) |
| STC Rating (Per Construction Type) | 63.0 | — | — |
Packaging & Availability
- Packaging
- 310ml/Tube; 25Tubes/CTN
- 20 fl . oz./Sausage
- 20 Sausages/CTN
- 5Gal./Pail (Sprayable)
Storage & Handling
- Storage Temperature
- 50 - 95 °F