Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Base
- Water-based Acrylic Insulation Coating
- Gloss
- Flat
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- Excellent thermal insulation at low thickness
- Excellent personnel protection
- Prevents Corrosion Under Insulation (CUI)
- Provides condensation protection
- Fast cure times
- Low VOC Product
- Easy application to irregular surfaces and tight spaces
- Features & Benefits
- Environmentally-friendly
- Passes FMVSS 302
- Saves installation time and waste compared to cut-and-paste systems
- Durable enough to go on roofs and underbodies
- Prevents corrosion and rust
- Lightweight
- Eliminates stocking of multiple insulation parts
- Withstands temperatures up to 350°F
- Helps reduce vibrations and noise
- Seals and protects surfaces
Applications & Uses
- Applications
- Priming
Self priming over non-ferrous materials (stainless steel & aluminum). Primer required for carbon steel substrates.
- Limitations
Applications should not exceed 350˚F.
- Substrates & Surface Protection
- Surface Preparation - Surface should be dry and free of foreign matter. Surface prep can be used to NACE 1-3 (SSPC SP 5-6) when applicable.
- Ferrous Surfaces - Should be primed prior to application of MI-DTI Insulating Coating. Since the coating is waterbased, it is important to have a boundary layer of protection to prevent flash rusting.
- Non-ferrous Surfaces - The coating can be applied directly to nonferrous surfaces. Surface should be clean and free of any oil, dirt or other foreign matter.
- Application Equipment
- Airless Sprayer
- Pump Ratio - 33:1 or larger
- Output per Cycle - 180cc (Minimum), 290cc (Optimum)
- Volume - 1.5 gpm (5.7 lpm) or greater
- Hose - 3/8” or larger with no more than 3’ of 1/4” whip. 1/2” hose recommended for length above 50’.
- Tip Size - 0.017” (for tight spots), 0.019 - 0.023” (Normal use)
- Pressure - Minimum of 3000 psi
- Small Spray Application - This sprayer is excellent for small applications and touch-ups.
- Brush or Roll - Not recommended for this coating
- Airless Sprayer
- Application Conditions
- Surface Temperatures - Surface temperatures for applications should be greater than 60˚F. Lower surface temperatures will increase dry times.
- Applications - Ambient & Cold (60˚F - 139˚F): For temperatures (surface or ambient, whichever is lower), an initial tack coat is recommended of 10 mils. This tack coat will help eliminate sag on vertical wall applications. Tack coat should be dry to touch prior to next pass. Typical coat thickness should not exceed 20 - 22 mils wet. The coating can be reapplied after each coat is thoroughly dry. Hot (>140˚F or >60˚C).
- Application Thickness - Product can be applied in successive coats to increase insulation ability. There are no upper limitations.
- Dryfall - Dryfall within a 3ft radius
- Mixing & Thinning
- Mixing - Only a mud mixing paddle should be used. Use 1/2” drill motor to stir contents with paddle. Make sure drill is set to reverse to ensure that the paddle will not mar the bucket’s inner wall. Please consult Mascoat for paddle, if needed. Do not mechanically shake.
- Thinning - Do not thin unless authorized in writing by Mascoat.
- Pot life - Coating is one part, so no catalyzation is needed. Pail can be reused if properly sealed.
- Clean Up
Equipment may be cleaned with soap & water.
- Cure Times
Temperature Cure Time 50 - 60˚F 60 - 72 hrs 61 - 70˚F 48 - 60 hrs 71 - 80˚F 36 - 48 hrs 81 - 90˚F 20 - 24 hrs 91 - 100˚F 18 - 20 hrs min. 100˚F 14 - 16 hrs - Uses
- Engine covers
- Undercarriages
- Roofs
- Firewalls
- Storage areas
- Generator
- Housings
- Doors
- Chassis
- Floors
- Hoods
- And much more
Properties
- Typical Properties
- Technical Data
- Specifications
| Value | Units | Test Method / Conditions | |
| Wet Weight | 6.4 - 6.5 | lbs/gal | — |
| Weight Dry Film To Area (20 mils DFT) | 0.046 | lbs/ft² | — |
| Volume Solids Content | 78 - 80 | % | — |
| Average Thickness per Coat (WFT, 70°F - 130°F) | 20 - 22 | mils | — |
| Practical Dry Coat Coverage (20 mils) | 50 - 55 | ft²/gal | — |
| VOC Content | 0.06 | g/l | — |
| Value | Units | Test Method / Conditions | |
| Permeability | Low - None | perms | — |
| Pull Apart Strength | 200.0 | psi | — |
| Application Temperature | 60 - 300 | °F | — |
| Operation Temperature | max. 350 | °F | — |
| Value | Units | Test Method / Conditions | |
| Hardness (Average) | 68.0 | Shore A | ASTM D-2240 |
| Mandrell Bend | 2022-01-02 | " | ASTM D-522 |
| Pull Apart Strength | 200.0 | psi | ASTM D-4541 |
| Impact Testing (Direct) | 80.0 | in.lb | ASTM D-2794 |
| Impact Testing (Direct) | 40.0 | in.lb | ASTM D-2794 |
| Flammability | Pass | — | FM VSS 302 |
| Flame Developed | Class A | — | ASTM-E-84 |
| Smoke Developed | Class A | — | ASTM-E-84 |
Technical Details & Test Data
- Dry Times Vs Humidity
Surface Temperature % Humidity Time Between Coats (hours) 61˚F - 70˚F 10-30% 4.00 31-50% 5.50 51-70% 6.50 min. 70% 8.00 71˚F - 80˚F 10-30% 2.00 31-509% 3.00 51-70% 3.50 >70% 4.00 81˚F - 90˚F 10-30% 1.50 31-50% 2.00 51-70% 2.50 >70% 3.00 91˚F - 100˚F 10-30% 1.25 31-50% 1.50 51-70% 1.75 >70% 2.00 101˚F - 110˚F 10-30% 1.00 31-50% 1.25 51-70% 1.50 >70% 1.75 111˚F - 120˚F 10-30% 0.75 31-50% 1.00 51-70% 1.25 >70% 1.50 121˚F - 130˚F 10-30% 0.50 31-50% 0.75 51-70% 0.75 >70% 1.00 Use 90˚ thumb test or moisture meter prior to recoat. Moisture readings should be less than 12% prior to recoat and 0% prior to topcoating. This is the estimated dry time for 15─20 mils (0.38 - 0.50 mm) of Mascoat Industrial-DTI wet. Dry time may vary depending on other conditions such as wind or enclosed environments. Lighter thickness passes will expedite dry times. Forced ventilation in confined areas will also expedite dry times.
Safety & Health
- Safety
For minimum protection, Mascoat recommends an N95 particulate respirator mask. For additional protection, a half mask respirator with organic vapor cartridge can be utilized. Eye protection recommended due to spray application method.
Packaging & Availability
- Packaging
- Container Wet (with pail/lid) - 35 - 36 lbs/5 gallon pail
- Net Contents - 32.2 lbs/5 gallon pail
Storage & Handling
- Storage
Do not subject wet coating in pail form to freezing conditions. Coating should be kept in a warehouse between 60˚F and 90˚F.
- Storage
Do not subject wet coating in pail form to freezing conditions. Coating should be kept in a warehouse between 60˚F and 90˚F.
- Shelf Life
18 months shelf life from manufacture date.