Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Product Highlights
MICOROX® FLOORLIFE™ PRIMER isa two component 77% solids epoxy primer formulated for use with FLOORLIFE™ Flooring Systems. Featuring low viscosity, this primer will provide deep penetration. FLOORLIFE™ PRIMER offers a long working life and excellent adhesion.
- Features
- Outstanding adhesion
- Deep penetration
- Long working life
- Moisture tolerant
Applications & Uses
- Applications
- Compatible Substrates & Surfaces
- Applications
Use MICOROX® FLOORLIFE™ PRIMER as a a base with MICOROXcoat FLOORLIFE™ DF, FLOORLIFE™ CP, FLOORLIFE™ SF and FLOORLIFE™ HTX.
- Surface Preparation
Proper surface preparation is the most important part of the application process. Prepare the surface in accordance with the MICOROX® FLOORLIFE™ PRIMER installation instructions. Slabs below grade should be over an effective moisture barrier. Clean and prepare the concrete by mechanical means andlor acid etch until all foreign matter has been removed. A rough surface is desired to provide a good bonding profile.
Coverage : 250 Sq. Ft/Gal.
Note : Coverage and number of coats may vary depending upon the nature of the surface being coated.
- Application
- Insure that the surface to be coated is clean, sound and free of grease, oil and old coatings.
- Read and understantad all label warnings and the material safety data shecet.
- Remove ignition sources from work and insure adequate ventilation.
- Combine one volume of resin and one volume of hardener in an appropriate container and mix for 3 - 5 minutes.
- Make sure that the area of application is well ventilated and that the air will not vent into any other occupied area.
- Apply MICOROX® FLOORLIFE™ PRIMER using a brush on roller.
- Temperature Limitations
During the installation and cure, surface temperatures of 60°Fto 80°Fare recommended.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Flash Point Resin | max. 250 | °F | — |
| Weight per Gallon Resin | 9.34 | — | — |
| N.V.W. (Resin) | 830.0 | cps | — |
| N.V.V. (Resin) | 100.0 | % | — |
| Viscosity Resin | 100.0 | cps | — |
| V.O.C. (Resin) | 0.0 | g/l | — |
| Flash Point Hardner | 81.0 | °F | — |
| Weight per Gallon Hardner | 7.65 | — | — |
| N.V.W. (Hardner) | 25.0 | cps | — |
| N.V.V. (Hardner) | 49.9 | % | — |
| Viscosity Hardner | 47.87 | cps | — |
| V.O.C. (Hardner) | 460.2 | g/l | — |
| Value | Units | Test Method / Conditions | |
| Mixing Ratio (by Volume) | 1 to 1 | — | — |
| Mixing Ratio (by Weight) | 1.22 to 1.0 | — | — |
| Coverage | 250.0 | sq. ft. per gallon | — |
| Thickness (Dry) | 4.7 | mils | — |
| Pot Life (77°F) | 2.0 | hours | — |
| Weight per Gallon | 8.5 | pounds | — |
| Viscosity (77° F) | 65.0 | cps | — |
| Tack Free Time | 12.0 - 20.0 | hours | — |
| Recoat time | 1.0 - 20.0 | hours | — |
| N.V.W. | 77.4 | % | — |
| N.V.V. | 73.9 | % | — |
| V.O.C. | 230.1 | g/l | — |
Safety & Health
- Precautions
MICOROX® FLOORLIFE™ PRIMER is intended for industrial and commercial use only. Use only in properly ventilated areas. Prolonged contact with skin can cause irritation. chemical splash goggles to avoid eye contact. Wear a respirator rated for organic solvents when applying this product in poorly ventilated Wear protective clothing and areas. Make sure that you have proper ventilation.Flammable!! Remove all sources of using. Ignition before
Packaging & Availability
- Packaging
Available in 2 gallon, 4 gallon and 10 gallon kits. Each kit will contain two containers.