Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- B/L Description
Paint and Related Materials NOIBN Protect From Freezing
Features & Benefits
- Ready-to-Use Product Features
- Unique Advantages
- Exterior Use (Limited to 21 days exposed)
- Prevention of natural tannin oil migration
- Vertical Hang - Apply up to 5-7 wet mils without paint film sag
- High solids % improves productivity
- Fast dry-to-sand and powdering
- ldeal basecoat for ALL M.L Campbell topcoats
Applications & Uses
- Markets
- Applications
- Uses
As a primer / undercoater on unfinished MDF and softwoods such as pine and cedar. Also, ideal for application on hard woods such as oak, poplar, birch and maple.
- Application
Application Procedure
All surfaces should be properly sanded. On wood or MDF, apply one or two coats of AQUIFI WB UNIVERSAL PRIMER. Wet film application should be 4 – 5 wet mils per coat. Scuff sanding between coats is recommended. Any M.L. Campbell® water-borne or solvent topcoats can be applied over AQUIFI WB UNIVERSAL PRIMER. If using solvent borne topcoat ensure primer is thoroughly dry (min. 2 hours dry time at 4-5 wet mils and at 75F and 50% humidity). Lower temperatures and higher humidity will extend dry times. When using AQUIFI WB UNIVERSAL PRIMER as a white primer under a clear topcoat, it is
recommended to use Non-Yellowing Clear Conversion Varnish to minimize yellowing.Note: Hot spray application is not recommended. Apply using only stainless steel or plastic spray equipment. Before application material, surface and air temperatures should be a minimum of 65°F.
Tinting
AQUIFI™ WB UNIVERSAL PRIMER can be tinted with GIW, Pratt & Lambert or Puratoner WB colorants, up to 3 ounces per gallon maximum.
Equipment Clean Up
- All equipment should be flushed with warm water or water/alcohol immediately after use.
- A subsequent flush with alcohol will ensure all moisture is removed from equipment.
Surface Preparation
- New Work: Remove any dirt, grease or other contamination and sand as required.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry. Finish as new work.
Reduction
No reduction is required. However, small amounts of clean water may be used for specific equipment. Over-thinning due to the high solids content of this product can cause sags and potentially reduce stainblocking properties. Thinning should be limited to 5-10%.
Caution
- THESE PRODUCTS ARE DESIGNED FOR SHOP APPLICATION AND PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or the Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 12.35 - 12.85 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 35 - 45 | sec | - |
| Solids by Weight | 62 - 66 | % | - |
| Solids by Volume | 43 - 47 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 691 - 741 | sq. ft. per gallon | - |
| Flash Point | Not Combustible | - | PMCC |
| Packaged VOC | 11.4 - 12.6 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 10 - 20 | minutes | - |
| Sanding Dry (At 77°F) | 30 - 40 | minutes | - |
| Stacking Dry (At 77°F) | 8.0 | hours | - |
Regulatory & Compliance
- Compliance
GREENGUARD certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons Pails, and Drums.
Storage & Handling
- Shelf Life and Storage
- Protect from freezing and other temperature extremes. This product is unusable if frozen.
- Store in airtight containers
- Shelf life is (1) one year.