Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263 3 PG III
Features & Benefits
- Ready-to-Use Product Features
- Unique Advantages
- Exceptional scratch/mar, chemical, and moisture resistance
- Unique alkyd/acrylic hybrid technology resists yellowing
- 10:1 mix ratio utilizing just one catalyst
- Easy-to-use formulation – up to 4 hour pot life
- Fast drying to help increase production times
- Excellent sanding and polishing characteristics
Applications & Uses
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Uses
CODA Interior Hybrid Polyurethane Black Primer’s formula is specifically designed for interior wood surfaces that are exposed to moisture, heat and household chemicals. It can be used for table tops, bar tops, cabinets, millwork, furniture, fixtures, and other wood surfaces.
- Application
Application Procedure
An excellent, very durable, exceptional build finish can be developed following a range of schedules listed below. Apply each coat at 3-4 wet mils. Note that CODA Interior Hybrid Polyurethane Black Primer should be used under the CODA Interior Clear Hybrid Polyurethane topcoat. Apply 1st coat of CODA Interior Hybrid Polyurethane Black Primer over sanded wood substrate. Wait about an hour and then sand using no finer the 320 grit silicon carbide sandpaper. Repeat Primer step as necessary. Apply 1st coat of CODA Interior Clear Hybrid Polyurethane topcoat. Wait about an hour and then sand using no finer then 320 grit silicon carbide sandpaper. Apply 2nd coat of CODA Interior Clear Hybrid Polyurethane topcoat. If 3rd coat is desired, wait an hour and then sand using no finer then 320 grit silicon carbide sandpaper and then apply 3rd coat of CODA Interior Clear Hybrid Polyurethane topcoat. Sanding is always recommended between coats. Wet on tack applications are acceptable within 2 hours of initial application. Do not exceed 8 dry mils. Before application, material, surface and air temperature should be a minimum of 680°F.
Note: For clean-up use PS3 Reducer or PS1 Fast Reducer. For retarder use PS5 Retarder. Do not use other solvents.
Mixing
CODA Interior Hybrid Polyurethane Black Primer has been developed to crosslink with C41077 CODA NonYellowing Catalyst. Mixing ratio by volume is 10:1 or 100 parts of CODA Interior Hybrid Polyurethane Black Primer to 10 parts of C41077 CODA Non-Yellowing Catalyst (which is a 10% catalyzation rate). Always mix before using. No waiting/induction time after mixing is required. Reduce as indicated in previous section. Pot life is up to three (3) hours and will be affected by temperature and humidity (higher temperatures and humidity levels will decrease pot life times). Product viscosity will rise as pot life expires. Do not attempt to extend pot life.
Equipment Clean Up
- Use PS3 Reducer or PS1 Fast Reducer to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner
Surface Preparation
- New Work: Remove any dirt, grease, glue or other construction contaminants and sand wood as required.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry, sand as required. Finish as new work. If cratering develops on work, Fish Eye Killer WR5 may remedy this problem (if the contaminant is not too severe).
Reduction
When used with conventional air spray, HVLP, air assisted airless spray, or airless spray, CODA Interior Hybrid Polyurethane Black Primer should be reduced 15-20% by weight with the PS3 series of solvent blends to achieve optimal flow and leveling. The amount of reduction necessary is dependent on the type of equipment being used. Please refer to the PS series usage chart for specific reducer recommendations. Consult your local VOC regulations before purchasing and applying these products.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Color
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 8.86 - 9.26 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 90 - 110 | sec | - |
| Solids by Weight | 47 - 51 | % | - |
| Solids by Volume | 34 - 38 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 556 - 606 | sq. ft. per gallon | - |
| Flash Point | 24.0 | °F | PMCC |
| Packaged VOC | 556.0 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 30 - 45 | minutes | - |
| Sanding Dry (At 77°F) | 60.0 | minutes | - |
| Stacking Dry (At 77°F) | 6.0 - 8.0 | hours | - |
Regulatory & Compliance
- Compliance
GREENGUARD Certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails.
Storage & Handling
- Shelf Life and Storage
- Package life is (3) three years - Store in a cool dry area in the original sealed containers.
- Do not store around any source of flames or sparks.
- Spills should be cleaned up with non-sparking tools and inert absorbent material.