Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263 3 PG II
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Uses
EnviroClaw Formaldehyde Free Pre-Cat White Primer can be used on wood or MDF board, store fixtures, cabinetwork, interior paneling and trim, furniture or any application where a fast dry primer with excellent product handling characteristics is required. Amazing Glaze may be applied over EnviroClaw if you allow EnviroClaw to dry at least 12 hours. Formulated for job shop application.
- Application
Application Procedure
Catalyzed type coatings develop very durable finishes but require controlled procedures. Do not apply material in too heavy a film (4 to 5 mils wet are recommended). Too much coating weight can cause recoating and durability problems. A thorough sanding between coats is always recommended. An excellent, very durable base coat can be developed by applying just one coat (apply no more than two coats) on wood and two coats on MDF board. Recommended total finish system dry mil thickness after sanding, should not exceed 4-6 dry mils. Always agitate thoroughly during application. EnviroClaw Formaldehyde Free Pre-Cat White Primer has excellent sanding characteristics. When sanding between coats, use Fre-Cut (no-fill) type sand paper. EnviroClaw may require larger tip than a typical lacquer.
Note: Hot spray application is not recommended. If hot spray equipment is used, temperature settings should never be over 110°F.
Mixing
Mix well before using. Material may separate during long-term storage.
Tinting
EnviroClaw Formaldehyde Free Pre-Catalyzed White Primer can be tinted using up to 6 ounces of MLC IC Colorant. DO NOT tint with glycol containing colorants. EnviroClaw is not a controlled tint base.
Equipment Clean Up
- Use lacquer thinner to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner.
- Solvent or lacquer-soaked rags should be stored in water-filled, closed containers prior to disposal
Surface Preparation
- New Work: Remove any dirt, grease or other contamination and sand as required, prior to finishing.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry. Finish as new work.
Reduction
When used with conventional air spray, HVLP, air assisted airless spray, or airless spray, EnviroClaw Formaldehyde Free Pre-Cat White Primer should be reduced 10-20% with M.L. Campbell Lacquer Thinner C16036, or Care Reducer C1621. The amount of reduction necessary is dependent on the type of equipment being used.
Testing
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, customers should test the complete system for adhesion and compatibility under their conditions prior to full-scale application.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
Value | Units | Test Method / Conditions | |
Weight Per Gallon | 9.8 - 10.2 | lbs/gal | — |
Viscosity (At 77°F) | 1200 - 1400 | cps | — |
Solids by Weight | 29.6 - 79.6 | % | — |
Solids by Volume | 32.8 - 37.8 | % | — |
Theoretical Coverage (At 1 Mil Dry) | 565.0 | sq. ft. per gallon | — |
Flash Point | 30.0 | °F | PMCC |
Packaged VOC | 541.0 | g/l | — |
Photochemically Reactive | No | — | — |
Value | Units | Test Method / Conditions | |
Dry to Touch (At 77°F) | 10 - 15 | minutes | — |
Recoat (At 77°F) | 30 - 35 | minutes | — |
Handle (At 77°F) | 60.0 | minutes | — |
Regulatory & Compliance
- Compliance
550 VOC compliant, GREENGUARD® Certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails.
Storage & Handling
- Shelf Life and Storage
- Shelf life is 1 year - Store in cool, dry areas in the original sealed containers
- Do not store around any source of flames or sparks
- Spills should be cleaned up with non-sparking tools and inert absorbent material