Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263 3 PG II
Features & Benefits
- Labeling Claims
- Materials Features
- Ready-to-Use Product Features
- Unique Advantages
- Designed to fill open grain for full fill appearance (build up to 10 mils)
- Moisture resistant
- Fast drying
- Extra high build
Applications & Uses
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Uses
It gives good sag resistance and can be sprayed from 4-10 wet mils on a vertical surface. It can also be built with multiple thin coats to get 10 - 12 dry mils by allowing each coat to dry thoroughly.
- Application
Application Procedure
Level Sealer™ is formulated to be ready to spray after catalyzing and has excellent sanding between coats. Use a Fre-Cut (no-fill) type sand paper. Always sand white wood (unfinished) with no finer than 150-grit sand paper before application of Level Sealer.
Mixing
Level Sealer™ has been developed to start its cross-linking (drying) with the addition of 12.8 ounces of C1491 Care Catalyst per gallon (10:1 ratio). Always mix in the catalyst thoroughly before application. No waiting period (sweating in time) is necessary before using this product. Level Sealer™ has a 24-hour pot-life once catalyzed; however, pot-life can be affected by some environmental factors such as high temperatures.
Equipment Clean Up
- Use lacquer thinner to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner.
- Solvent or lacquer soaked rags should be stored in a water filled, closed containers prior to disposal
Surface Preparation
- New Work: Remove any dirt, grease, glue or other construction contaminants and sand wood as required.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry, sand as required. Finish as new work. If cratering develops on work, Fish Eye Killer WR5 may remedy this problem (if the contaminant is not too severe).
Reduction
Level Sealer™ requires no reduction. If reduction is necessary, use only M.L. Campbell Lacquer thinners or retarders.
Testing
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, customers should test the complete system for adhesion and compatibility under their conditions prior to full-scale application.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 7.79 - 8.39 | lbs/gal | - |
| Viscosity (At 77°F) | 440 - 640 | cps | - |
| Solids by Weight | 43 - 47 | % | - |
| Solids by Volume | 35 - 39 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 574 - 624 | sq. ft. per gallon | - |
| Flash Point | 70.0 | °F | PMCC |
| Packaged VOC | 525.0 | g/l | - |
| Packaged VOC (Catalyzed 10% w/C1491) | 541.0 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 30 - 60 | minutes | - |
| Sanding Dry (At 77°F) | 60.0 | minutes | - |
| Stacking Dry (At 77°F) | 5 - 8 | hours | - |
Regulatory & Compliance
- Compliance
GREENGUARD Certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails.
Storage & Handling
- Shelf Life and Storage
- Package life before catalyzing is three years -Store in a cool dry area in the original sealed containers.
- Do not store around any source of flames or sparks.
- Spills should be cleaned up with non-sparking tools and inert absorbent material. If stored at temperatures below 30°F, this product may gel. If so, warming to room temperature will restore it to useable condition