Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Composition
- 2-Part Aliphatic Polyurethane
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Universally Compliant, Environmentally Friendly, LowVOC
- CASection 01350 Compliant- Qualifies for LEED IAQ Credits
- HAPS Free (Hazardous Air Pollutants), No Fumes
- Suitable for USDA Inspected Facilities
- Top Tier Chemical, Solvent, Water, Oil and Grafiti Resistance
- Outstanding Hardness, Durability and Abrasion Resistance
- Top Tier Cleanability and Stain Resistance
- Resistant to Hot Tire Pick-Up
- Flash Rust Inhibitive formula for DTM Environments
- Creates a Top Tier Dry Erase Environment
- High Solids, Versatile General Maintenance Coating
- Available in High Gloss 90°, Matte 5°, Clear or Colors
- When the surface temperature is between 50-70°F, the Permashield 200 can be accelerated for same day returnto service.
Applications & Uses
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Basic Uses
Permashield 200 can be applied to interior, exterior, vertical or horizontal, concrete, masonry, stucco, wood, vinyl-composite tile (VC), and prepared ferrous and non ferrous metals, etc. It can be used as an industrial or residential coating for: commercial buildings, convention centers, stadiums, hospitals, warehouse floors, garages, universities, airports, shopping centers, schools, food processing plants, transportation, government facilities, etc.
Permashield 200 is urine resistant for use in pet & dog kennels
- Application
Surface Preparation
Surfaces must be clean, dry and free of chalk, grease, oils, salts and contaminants that inhibit proper adhesion.
- Concrete And Masonry: Must be cured at least 28 days. Level protrusions and repair cavities, voids, holes, cracks, etc. that are larger than 1/16". Dense, non-porous concrete should be grinded, sandblasted, abrasive blasted (ASTM D4259), acid etched (ASTM D4260), or primed with Monochem 21.
- Non-Ferrous Metals (galvanized, aluminum, stainless steel): Remove all oils or films with a neutral detergent or emulsion cleaner. Blast lightly with fine abrasives or conduct a light etching. Then rinse the surface with Zinc and apply Permashield 200 within 3 hours to avoid rust oxidation.
- Ferrous Metals: Remove all the loose rust, dirt, grease or other contaminants by one of the following depending on the degree of cleanliness required. Blast SSPC-SP3; SSPC-SP2; SSPC-SP6; SSPC-SP7. Blast lightly with fine abrasives or conduct a light etching. Then rinse the surface with Zinc and apply Permashield 200 within 3 hours to avoid oxidation.
- Water Based Painted Surfaces (acrylic/latex): Lightly sand or abrade glossy surfaces to provide tooth. Oil Based Painted Surfaces: Prime with MONOCHEM 21. Conduct
- a thorough test patch and adhesion test. Caution: Horizontal surfaces coated with Permashield 200 can become slippery when exposed to moisture.
Recommended Primers:
- Monochem 21: Ideal for non-porous surfaces and coating over water/oil/solvent/alkyd/unknown based coatings.
- Monobond: Ideal for coating over single component water based coatings and most smoother surfaces.
- Aquaprime: For surfaces containing a PH of 8-16.
- Monobond RI: For surfaces requiring a rust inhibitive primer.
Mixing Ratio:
- Mixing Ratio - 2.5:1
- One Gallon Kit:
- Part A: 80 OZ
- Part B: 32 OZ
- One Gallon Kit totals: 112 oz (not a full gallon)
- Approximate Coverage: 175 - 250 sq. ft. per kit (1 Coat)
- Five Gallon Kit:
- Part A: 400 OZ
- Part B: 160 OZ
- Five Gallon Kit totals: 560 oz (totals 4.375 gallons)
- Approximate Coverage: 875 - 1,250 sq. ft. per kit (1 Coat)
Mixing
- Stir Part A to disperse product.
- Pour the entire contents of Part B into Part A.
- Mix for 3-5 minutes. No partial mixing.
- For spray applications, the viscosity may be reduced with water at a maximum of 8 ounces per gallon. Add siowly to the mixture while stirring.
- Do notuse mixed product after 2 hours.
Application: A continuous application will ensure a smooth and level coat that is free of lines and streaking. Applications should not be stopped part way across an area and completed later.
Two coats of Permashield 200 are required. For concrete surfaces, apply at a spread rate of 175-250 square feet per gallon (depending on surface porosity), yielding 3-4 dry mils per coat. For metal surfaces, apply at an approximate spread rate of 300 square feet per gallon. Do not exceed 5 wet mils because micro bubbling or hazing may occur. To obtain proper adhesion between coats it is imperative that recoating be done within 4-6 hours (do not exceed 12 hours between coats or sanding may be required).
For best results use the best quality roller, brush, or airless sprayer. Extra care should be taken not to cause air bubbles. For larger jobs we recommend using a sprayer. Permashield 200 can be applied directly to cleaned and properly prepared coatings like water based acrylics, epoxies and urethanes. Abrade and clean the previous paint to provide tooth for the new coating.
In all applications, we require conducting a test patch to ensure proper compatibility, adhesion and appearance. All surfaces must be tested before doing the entire project. Prime with Monochem 21 if there are adhesion issues with Permashield 200.
Standard Dry Time:
- Light Foot Traffic: 24 Hours
- Heavy Objects: 5 Days
- Full Cure: 5 Days
- Full Foot Traffic: 48 Hours
- Hot Tire Resistance: 5 Days
- Full Chemical Resistance: 5 days
Accelerated Dry Time: In cooler environments (< 75°F), use Accelerator P200 (2 oz/ gallon) with PERMASHIELD 200 to improve the dry/cure time.
- Pot Life: 15-20 minutes
- Foot Traffic: 6-8 Hours
- Recoat Time: 1-2 Hours
- Hot Tire Resistance: 24-48 Hours
Tinting: Always test for compatability before tinting the Permashield 200. Only use high quality waterborne industrial pigments.
- White Base Maximum Tint Load: 4 Oz.
- Neutral Base Maximum Tint Load: 8 Oz.
Precautions:
- Do not apply heavier than 5 wet mils per coat to avoid micro blistering and an over applied milky appearance.
- Air and surface temperatures must be between 50°F-90°F during the application.
- Do not apply during windy conditions. Protect surrounding areas
- from over spray.
- Do not apply if rain is eminent within 48 hours after application.
- Do not dilute. Use as-is.
- Do not apply to surfaces containing > 15% moisture.
- Do not apply to surfaces displaying a pH over 8.
- Do not apply to surfaces that have hydrostatic pressure.
Equipment Clean Up: Equipment should be cleaned with water or a mild detergent immediately after use. Clean all the equipment while the material is fresh or a legally compliant paint remover may be required.
Properties
- Finish (60°)
- Gloss (85 - 90°), Matte (5 - 10°)
- Physical Properties
- Performance Properties
- Conditions
* - Cooler Temperature, higher humidity and film thickness will require longer drying time.
Value | Units | Test Method / Conditions | |
Volatile Organic Compounds | max. 5 | g/L | ASTM D3960 |
Solids (Clear, By Weight) | 52 - 56 | % | — |
Solids (White Base, By Weight) | 59.0 | % | — |
Solids (By Volume) | 51 - 55 | % | — |
Weight (1-Gallon Kit) | 10.0 | lbs | — |
Mixed Viscosity (75°F) | 85 - 90 | KU | — |
Coverage | 220- 275 | Sq. Ft per Gallon | — |
Recommended Dry Mils | 3 - 4 | mils | — |
Recommended Wet Mils | 5 - 7 | mils | — |
Dry Time (Dry Hard) | 2.0 | Days | — |
Dry Time (Recoat) | 4 - 6 | Hours | — |
Value | Units | Test Method / Conditions | |
Tensile Strength | 5950.0 | psi | ASTM D412 |
Pencil Hardness | 2H | — | ASTM D3363 |
Elongation Modulus (100%) | 4190.0 | psi | ASTM D412 |
Impact Resistance | 160.0 | In/Lbs | ASTM D2794 Reverse |
Taber Abrasion Resistance | max. 45 | mg loss/1000 cycle | ASTM D4060 |
Adhesion (Porous Concrete) | 2901.0 | psi | ISO 4624 |
Adhesion (Sanded Ferrous Metal) | 2792.0 | psi | ISO 4624 |
Outdoor Weathering | 8000.0 | Hours | ASTM G155 |
Salt Fog Spray (Alumnium) | 750.0 | hours | ASTM B117 |
Cyclic Weathering (Maximum change of 10 gloss level) | No blistering, cracking, softening or delamination. | — | AASHTO R-31 |
Regulatory & Compliance
- Certifications & Compliance
- Product Qualifications / Approvals
Cal Green Yes OTC (Industrial Maintenance) Yes SCAQMD (Industrial Maintenance) Yes CARB (Industrial Maintenance) Yes LEED (New Construction) Yes LEED (New Schools / CHPS) Yes MPI Approved Product #205
Technical Details & Test Data
- Chemical Resistance (ASTM D1308)
MEK double rubs 300+ cycles Skydrol No effect after 7 days Brake Fluid No effect after 7 days Gasoline No effect after 7 days Motor Oil No effect after 7 days Betadine No effect after 24 hours 50% NaOH No effect after 24 hours |14% NH4OH No effect after 24 hours 10% Acetic Acid No effect after 24 hours 20% H2SO4 No effect after 24 hours 10% HCL No effect after 24 hours 10% Bleach No effect after 24 hours DI Water No effect after 24 hours IPA No effect after 4 hours Toluene No effect after 4 hours Acid rain No effect after 4 hours
Safety & Health
- Safety Information
Monopole Inc. recommends the use of aggregates for skid resistance in all of its floor coatings that may be exposed to wet, oily or greasy conditions. The type of activity on the floor surface may determine the degree of slip resistance required for a specific area. Monopole Inc. will not be responsible for injury caused in a slip or fall situation. It is the end users responsibility to test and determine the suitability and safety of our coatings for their particular use and application.
Packaging & Availability
- Packaging & Colors Available
Permashield 200 is available in clear or pigmented, matte or gloss finishes. Clear kits are packaged in a one-gallon kit and a five-gallon kit. Color kits are only available in one-gallon kits.
- Gloss:
- #5350: Clear
- #5360: White Base
- #5370 Neutral Tint
- Matte:
- #5355: Clear
- #5365: White Base
- #5375 Neu
- Gloss:
Storage & Handling
- Pot Life
- 1 - 2 Hours
- Shelf Life
- 1.5 Year (Gloss), 1 Year (Matte)
- Shelf Life
- Gloss Part A: 12 Months
- Matte Part A: 6 Months
- Part B: 12 Months.