Products

Murpec® SP is a High wear resistance; High compressive strength; Good slide properties; Good continuous temperature behavior. Production based on PEEK-SP.

Murinit® SP [FS], thanks to the low fiber content and integrated solid lubricant, this high-performance material offers an excellent combination of good slide and wear behavior, high strength, and dimensional stability – even at high temperatures. Murinit® SP also has a good resistance to chemicals and hydrolysis.Production based on PPS-SP.

The integration of 25% carbon increases the wear resistance, hardness, and creep strength of this material. Murflor®+ Carbon is used, for example, when electrical conductivity is required and Original Material "S"® Black Antistatic cannot be used because the ambient temperature is too high. Production based on PTFE-C.

This material has the same properties as Muralen® but also has an antimicrobial effect.Production based on PE-UHMW SG 2.1.

"Since the 1950s, Material ""S""® has been tried and tested a thousand times over for a wide range of applications in power engineering and conveyor technology Material ""S""® is based on virgin, ultra- high molecular weight low pressure polyethylene and significantly exceeds the requirements of DI n 16972. Original Material ""S""® is one of the most successful groups of materials in the industrial plastics sector. In particular, Original Material ""S"" green® has established itself as a branded product in the plastics sector. It is used in all applications where a technical, high- performance plastic is required. Original Material ""S"" green® is synonymous with excellent slide properties, high wear resi - stance, and a long lifetime." Production based on PE-UHMW SG 1.2.

The use of this highly temperature resistant polyamide enables reliable operation up to a constant service temperature of +155ºC. The material retains its rigidity and creep strength over the entire temperature range far better than other Murylon® types. Thanks to its increased resistance against oxidative degradation, it is usually used in applications at above +80ºC. Production based on PA46.

This material combines the excellent properties of the Murylon® range with additional high tensile and burst strength, increased wear resistance, and a lower level of moisture absorption than Murylon® B. Production based on PA66.

"Muralen® is based on high molecular weight polyethylene (PE-HMW) and is ideally suited for use in applications that require the generally impressive material properties of polyethylene. However, it is only used in cases where the excellent slide and wear resistance properties of Original Material ""S""® are not required. Because of its great cut, impact, and shock resistance, this material is often used to make underlays for cutting and punching machines and for ram guards."

Murylon® A GF, the properties of this material surpass the already impressive characteristics of Murylon® A. This is possible thanks to admixed glass fibers. The result: A clear improvement in cold flow behavior and dimensional stability. This enables higher static pressure loads to be endured. Production based on PA66.

"Original Material ""S"" plus+® FP [FS]® is a new technical plastic that completely meets the requirements of the food sector for the detectability of plastic foreign bodies in foods. ""FP"" stands for ""food protect"" and embodies two vital properties: This product is both food-safe and metal-detectable. Metallic foreign bodies in foodsare safety detected by metal detectors and removed. However, plastic particles from plant components can be problematic. Thanks to the use of additives in Original Material ""S"" plus+® FP [FS], all commonly used metal detectors in the food industry can now detect and remove plastic particles. Furthermore, in the case of this material, particles even smaller than the required size for the detectability of metal (3 mm) can be found and removed: Particles of only 2mm in size (see the illustration) have been detected without any problems in tests." A member of the S plus family Production based on PE-UHMW SG 1.1.

The use of this plastic saves energy and improves the efficiency of your machines thanks to its low friction resistance. The sliding friction coefficient is reduced by up to 50 percent with this material – and so too the energy consumption for the drive power required. This plastic offers real energy-saving potential. Thanks to the additive used, Original Material ”S” ® plus+ LF ESD is electrically conductive, enabling voltage to be dissipated at maximum speed with the same maximum friction resistance. A member of the S plus family Production based on PE-UHMW SG 1.1.

This material results from the further development of a tried-and-tested material. Experiences of over 50 years of producing Original Material "S"® have contributed to the development of this material. This involved improving already impressive material properties. For example, the self-lubricating character of this material has resulted in an improved sliding friction coefficient in comparison with Original Material "S". Original Material "S" 8000® is ideally suited for use in sliding guides, slide segments, and slide bearings.

This material is used for applications that involve manufacturing and transportation at high pressure. The balance quantity of micro glass beads in Original Material "S" plus+® GB provide the combined benefits of extremely high molecular weight polyethylene and glass. The glass beads that protrude from the surface provide a rounded and hard sliding surface. A member of the S plus family Production based on PE-UHMW SG 1.1.

Original Material "S" plus+® AB contains special substances that prevent the growth of bacteria and other microbes at the same time as protecting the environment and people. The material is thus ideally suited for use when manufacturing and processing foods. It can reduce the growth of microbes on surfaces by between 99.96 to 99.99% in comparison with materials with no special additives. This means that it can virtually eradicate unpleasant smells and the formation of biofilm. Original Material "S" plus+® AB combines antibacterial properties with exceptional characteristics of the "S" plus+® family. A member of the S plus family Production based on PE-UHMW SG 1.2.

In comparison with other thermoplastics, Murpec® has an exceptionally low thermal expansion coefficient. This property provides optimum dimensional stability and means that dimensions do not change even if used in wet environments. Because of the high glass transition temperature, the material’s rigidity and strength are retained almost in their entirety even at high temperatures. Murpec® materials are extremely resistant to deformation and exceptionally abrasion-proof. Production based on PEEK.

The addition of 60% bronze to the base material reduces the expansion coefficient and gives lower sliding wear.Production based on PTFE-CuSn.

Murylon® B natural has the best impact resistance of all Murylon materials. This material is especially suited for use in machine construction thanks to an excellent combination of mechanical properties. Production based on PA6.

"Industrial applications are often subject to high temperatures at which Original Material ""S""® could previously not be used. Such applications require materials with familiar characteristics such as wear, impact, and chemical resistance. The new Original Material ""S"" plus+® TLS now offers - for the first time - a material that can be used in situations for which Original Material ""S""® was not suited. Even at high operating temperatures of up to120°C for short periods of time and constant service temperatures of up to100°C, the molecular structure of this ultra-high molecular weight low-densitypolyethylene does not change. This is because the thermal oxidation point has been increased through the use of a newly developed additive. ""S"" plus+® TLS is thus suitable for a wide range of industrial applications that are subject to sustained high temperatures." A member of the S plus family Production based on PE-UHMW SG 1.1.

Murtfeldt's answer to international demand for energy conservation and sustainability: Murtfeldt Original Material "S" plus+® LF When developing this material Murtfeldt managed tofurther slash the sliding friction coefficient by half. The particularly great feature of this material is that this value is constant and is achieved even at low friction intensities. The required driving force is drastically reduced, meaning that your motors need less energy and are thus significantly more economical to run. This innovative material enables an increased machine running speed at the same time as less abrasion and thus a lower maintenance requirement. As a result, the material significantly contributes to an increase in your productivity. A member of the S plus family Production based on PE-UHMW SG 1.1

"For the first time, it has been possible to develop a light plastic with high conductivity and a voltage-dissipating effect on earthed components. This combination was not previously possible. This material is ideal for use in applications where a high value is placed on hygiene and antistatic characteristics. In many work environments, light surfaces are mandatory. The conductivity of Original Material ""S"" plus+® Bright ESD provides optimum safety. Its properties largely match those of Original Material ""S"" plus+® ESD."

Original Material "S"® black has the same properties as Original Material "S"® green/natural. In addition, it is also electrostatically conductive due to the addition of additives.Production based on PE-UHMW SG 1.2.