Products

Nylene Very high viscosity extrusion resin having an ASTM relative viscosity of 800 Excellent structural strength, durability, and physical properties Good melt strength and good draw-down properties which promote dimensional control for extrusion of pipe, tubing, film, and sheet Particularly recommended for the extrusion of thick slab, large rod stock, and large complex profiles Optimum processing conditions should permit for a melt temperature of 550 - 575°F at the die.

Nylene 50% glass fiber reinforced, heat-stabilized nylon 6 injection molding resin Specifically designed for maximum strength and stiffness while maintaining the heat and chemical resistance typical of nylon 6 resins Suitable for brackets, enclosures, valve bodies, and other uses where maximum strength and stiffness are required

Nylene General purpose, 20 % glass fiber-reinforced poly(phenylene ether) (PPE) alloy Areas of application include water contact areas such as impellers and pump housings Suitable for applications such as motor housings which require high modulus and distortion temperature

Nylene Medium viscosity, fast cycle molding resin.Crystallization initiators provide fast molding cycles through rapid melt set-up.Parts molded from NX1440 have better dimensional stability at moisture equilibrium than parts molded from conventional nylon.Suitable for such uses as clips and fasteners, bushings, small levers, gears, and window hardware.Optimum processing conditions should provide a melt temperature of 460 - 480°F at the nozzle.

Nylene Recommended for molding applications requiring both maximum durability and toughness Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene Glass and ceramic fiber reinforced nylon 6 injection molding material Designed to provide high dimensional stability, very high stiffness, and a hard surface, while maintaining the heat and chemical resistance typical of nylon products Suitable for such uses as valve bodies, pump housings, hydraulic fittings and couplings, and other applications which require this unique set of characteristics

Nylene Nylon 6 polymer designed for use in extrusion coating and cast and blown filmExcellent grease resistance, toughness, and resistance to abrasion.Films made from Nylene® 615 C have barrier properties against oxygen and aroma typical of nylon 6.Meets the requirements of 21 CFR 177.1500 for food contact.

Nylene 33% glass fiber reinforced nylon 6/10 injection molding grade. Has the high strength and stiffness of reinforced nylon, while also having the reduced moisture pick-up associated with nylon 6/10 Suitable for pump housings, inlet housings, fittings, and other uses where moisture pickup may be a concern

Nylene Heat stabilized version of NYLENE 451 recommended for molding - Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene 43% glass fiber reinforced nylon 6/10 injection molding grade Has the high strength and stiffness of reinforced nylon, while also having the reduced moisture pick-up associated with nylon 6/10 Suitable for pump housings, inlet housings, fittings, and other uses where moisture pickup may be a concern

Nylene Duratel MF9-GF10 is 10% glass fiber reinforced general purpose acetal co-polymer. Duratel MF9-GF10 has increased strength and stiffness over unreinforced acetal. MF9-GF10 retains the chemical resistance and lubricity inherent in acetal materials. This product is suitable for brackets and levers, valve bodies, and other applications requiring this unique blend of properties.

Nylene General purpose, 30 % glass fiber-reinforced poly(phenylene ether) (PPE) alloy Areas of application include water contact areas such as impellers and pump housings and motor housings which require high modulus and distortion temperature UL recognitized