Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- Seals cutback glues, asbestos mastics, VCT, or VAT tile
- Meets EPA guidelines to not dissolve or disturb mastics
- No need for scraping, grinding, solvents, soy gels, or removal of mastics
- Nontoxic; no harmful VOCs
- Safe and easy to use
- Applies with roller or brush
- For use indoors and outdoors
- Comes ready to use
- Cleans up with water
- Benefits
- Seals wood, VCT and VAT tile, concrete, and black asbestos mastics
- Prepares floors for new paint, tile, epoxy, or decorative/leveling cements
- Creates a primed surface ready for new coatings
Applications & Uses
- Applications
- Compatible Substrates & Surfaces
- How to use PerfectPaint
- Remove any debris from the floor such as dust, rubble, and any loose or broken tiles
- Wash floor with PerfectCleaner and rinse with clean water
- If floor requires patching, apply patching cement and/or 100% acrylic caulk as needed
- Apply first coat of PerfectPaint. Allow 6 hours to dry
- Apply second coat of PerfectPaint. Allow 24 hours to cure
- Surface Preparation & Application Procedure
- Dissolve one half packet (4 oz) of PerfectCleaner into 3-5 gallons of warm water. Apply the PerfectCleaner using a stiff broom, mop, or deck brush. Once applied, rinse/mop the suds and dirt well with clean water. When the floor is dry to the touch, apply the PerfectPaint. Wheapplyingly PerfectPaint over existing tile or sheet vinyl: Use a wax stripper, wash surface, then apply
- PerfectPaint.
- To repair damaged areas and low Spots Preparations, use PerfectPrimer to spot prime substrate in areas to be patched. Once primer is cured, fill low spots with your choice of polymer modified cement patching materials. Small cracks or holes can be filled with acrylic caulk.
- Once all prep has been completed, use a brush or 3/8” nap roller to apply first coat . After 12 hours, apply your second coat.
- Apply PerfectPaint evenly by rolling it on as thickly as you can, and then backrolling so it does not puddle. If you are spraying a large area, use piston powered paint sprayer with a .27-.32 tip.
- After 24 hours you can walk on the floor, or install a floating wood floor, carpet, or sheet vinyl system.
- Allow for 24 hour cure before applying concrete and 48 hours before applying epoxy type coatings.
- When applying PerfectPaint over existing epoxy, acrylic sealers or other resinous floors: Remove loose and poorly adhered material. Lightly surface using a #100 Grit screen. Vacuum or sweep off grinding dust. Wipe down surface with acetone, or denatured alcohol, and then apply two thin coats of PerfectPaint.
- NOTE: When installing a new paint, epoxy, tile mastic or decorative cements, use PerfectPrimer. Always wear socks or booties to avoid tracking dirt onto the painted surface. Dirt and dust are bond-breakers.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Coverage (2 Coats) | 400 - 450 | Sq.ft/2 Gallon | — |
Regulatory & Compliance
- Certifications & Compliance
- Regulatory & Compliance
PerfectPaint is the only paint specified to meet the EPA guidelines to cover, prime, seal, and paint over asbestos mastics without disturbing them.
Technical Details & Test Data
- Perfect Primer & Perfect Paint Comparison
PerfectPrimer PerfectPaint Creates a primed surface ready for new coatings. Creates a finished, walkable paint surface. Seals wood, VCT and VAT tile, concrete, and black asbestos mastics. Seals wood, VCT and VAT tile, concrete, and black asbestos mastics. Prepares floors for new paint, tile, epoxy, or decorative/leveling cements. Prepares floors for new carpet, floating wood/vinyl flooring, laminate flooring, or sheet vinyl.