Products

Cel-Span® Process Aid 315N is an effective compatibilizer and coupling additive with an additional stabilizing package added with regrind Polypropylene and Polyethylene applications in mind. Cel-Span® Process Aid 315N recommended usage is 1.5% to 3.0%. We also recommend that the rear zone temperatures are reduced by 15% – 20% and the front zone by 5% – 10%. Compatibilization of dissimilar resins is achieved through a non-acidic means to prevent additional degradation of the previously compromised regrind systems being utilized. The use of Cel-Span® Process Aid 315N increases physical properties by 10% - 20% depending on types of materials used and regrind conditions. Fiberglass is better orientated with the use of Cel-Span® Process Aid 315N allowing improved izod and tensile rating with enhanced gloss and esthetics.

Cel-Span® Purge 388 is a transition purge that contains several proprietary additives that are essential in the cleansing cycle of high temperatures and lower melting polyolefins. Temperatures above 500 °F may cause material to smoke. Cel-Span® Purge 388 can be used directly without any mixing necessary to clean most plastic equipment during color and resin changes. The unique additives and resin system in Cel-Span® Purge 388 makes it possible to cleanse color resins in less time, in most resin applications.

Cel-Span® CFA 800 is an endothermic foaming agent concentrate recommended for injection molding & extrusion applications for a variety of thermoplastic resins such as polyethylene, polypropylene, styrenics, MPPO and ABS. Cel-Span® CFA 800 is recommended for extrusion, and structural foam molding of polyolefins, polystyrene, MPPO and ABS. This product exhibits a very fine cell structure compared to a typical endothermic foaming agent in extrusion applications. This product has been engineered to eliminate splay and to exhibit good surface esthetics for solid injection foam parts.

Cel-Span® CFA 844 is a highly loaded 80% active endothermic foaming agent formulated for applications with high gas requirements. Cel-Span® CFA 844 concentrate releases carbon dioxide gas upon decomposition. This product is safe when used under the conditions of intended use. Upon complete decomposition (activation) of the C.F.A., the extruded and injected parts will become white, a color common to endothermic chemical foaming agents.

Cel-Span® CFA 897 is a 40% active endothermic foaming agent concentrates recommended for extrusion applications for a variety of thermoplastic resins such as polyethylene, polypropylene, styrenics, MPPO and ABS. Cel-Span® CFA 897 is recommended for extrusion, and structural foam molding of polyolefins, polystyrene, MPPO and ABS. This product exhibits a very fine cell structure compared to a typical endothermic foaming agent in extrusion applications.

Cel-Span® CFA 899 is a 40% active endothermic foaming agent concentrate recommended for extrusion applications for a variety of thermoplastic resins such as polyethylene, polypropylene, styrene, MPPO, and ABS. Cel-Span® CFA 899 is recommended for extrusion, and structural foam molding of applications that require a very fine cell structure compared to a typical endothermic foaming agent in esthetic applications.

Cel-Span® FR 611 is a pelletized antimony and brominated concentrate that meets stringent flammability requirements defined by industry standards. Cel-Span® FR 611 is recommended for electrical sockets, timers, and light fixtures plus other applications where a UL rating is required.

Cel-Span® CFA 899PS is a 20% active endothermic foaming agent concentrate recommended for extrusion applications for a variety of thermoplastic resins such as polyethylene, polypropylene, styrene, MPPO, and ABS. Cel-Span® CFA 899PS is recommended for extrusion, and structural foam molding of applications that require a very fine cell structure compared to a typical endothermic foaming agent in esthetic applications.

Cel-Span® FR 680 is a highly loaded 80% concentrate flame retardant tailored for a variety of applications including injection molding and sheet extrusion. Cel-Span® FR 680 was designed to be a cost effective retardant made for polyethylene requirements including the Boston Fire Department Test and the NFPA – 701 small scale test. The use of Cel-Span® FR 680 will result in excellent flame retardancy to pass several flammability requirements. Flame testing has shown that recommended levels between 8% - 25% are intended as guidelines, but optimization is necessary for each application because of the differences between equipment, resin systems, additives and flame retardancy requirements.

Cel-Span® Process Aid 101 is a 100% active (powder or pellet) internal lubricant processing aid with anti-static properties that are incorporated into the resin. Cel-Span® Process Aid 101 eliminates the need for an external mold release agent and improves resin flow, dispersion, resin additives ex:(reinforcements, fillers, and pigments), and reduces cycle time. The use of Cel-Span® Process Aid 101 will not have an adverse effect on the physical properties. Compatible with Polyethylene, Polystyrene, and Polypropylene.

Cel-Span® Process Aid 305 contains a powerful water-seeking additive that chemically combines and eliminates lensing and porosity in blown and cast extrusion, injection, compounding, and pipe applications caused by surface moisture or incorporated into the resin during processing. CelSpan® Process Aid 305 contains a very effective additive that chemically traps water to eliminate moisture. This product can be used to eliminate moisture in high temperature engineering resins such as nylon and is utilized by metering in at 2% - 5% depending on the level of moisture.

Cel-Span® CFA 840 is a 40% active endothermic foaming agent concentrate, suitable for a variety of olefin resins such as polyethylene and polypropylene. Cel-Span® CFA 840 is recommended for extrusion, injection, and structural foam molding of polyolefins.