Knowde Enhanced TDS
Identification & Functionality
- Technologies
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Compatible Substrates & Surfaces
- Typical Applications
ES6209 has excellent adhesion to the composite and metal parts typically used in vehicle construction. Italso bonds rigid foam, wood, ceramics, fiberglass and most metals with equal
ease. When cured, ES6209 provides tough, durable structural joints.- Directions For Use
PREPARATION: All surfaces to be bonded or patched must be free of dirt, oil and grease.Sanding or roughening the area to be bonded increases the surface area and enhances thebond.
MIXING: Measure out equal parts of ES6209 A and B, combine and mix thoroughly until a uniformcolor and consistency is reached. Mix for at least 1 to 2 minutes, scraping the sides andbottom of the container to avoid leaving unmixed material that will cause soft spots in thecured material and poor bonds.
APPLICATION and CURING: Apply mixed material to the roughened area of the parts to bebonded. Press surfaces firmly together and let set 2 to 4 hours at 75°F. If necessary, place assemblyin a jig or other device to prevent movement during initial curing time. Curing time is18 to 24 hours at 75°F, or 2 to 3 hours at 140°F.
Properties
- Physical Form
- Mechanical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Gel Time (77°F) | 60 - 90 | min. | D2471 |
| Mixed Viscosity (77°F) | 45,000 - 55,000 | cps | D2393 |
| Cured Hardness | 85 | Shore D | D2240 |
| Cure Time (77°F) | 18 - 24 | h | — |
| Cure Time (140°F) | 3-Feb | h | — |
| Specific Gravity | 1.09 | — | D1475 |
| Tensile Strength | 8000 | psi | D638 |
| Elongation At Break | 7 | % | D638 |
| Compressive Strength | 11500 | psi | D695 |
| Aluminum to Aluminum Tensile Lap Shear (77°F) | 2900 | psi | D1002 |
| Aluminum to Aluminum Tensile Lap Shear (140°F) | 700 | psi | D1002 |
| Value | Units | Test Method / Conditions | |
| Mix Ratio (By Weight or Volume) | 100 : 100 | Wt. | PTM&W |
| Pot Life (4 fl. Oz. Mass At 77°F) | 60 - 90 | min. | D2471 |
Safety & Health
- Safety And Handling
PTM&W epoxy products are made from raw materials carefully chosen to minimoir zeveen eliminate toxic chemicals, and therefore offerthe user high performance products withminimum hazard potential when properly used. Generally, the PIM&W epoxy resins and hardeners will present no handling problems if users exercise care to protectthe skin andeves, and if good ventilation is provided in the work areas. However, all epoxy resins and hardeners can be irritating to the skin, and prolonged contact may result in sensitization;and breathing of mist orvapors maycause allergenic respiratory reaction, especially in highlysensitive individuals. As such, avoid contactwith eyes and skin, and avoid breathingvapors. Wear protective rubber apron, clothing, gloves, face shield or otheritemsas required to prevent contactwith the skin. Incase of skin contact, immediatelywashwithsoapand water, followed by a rinse of the area with vinegar, and then a furtherwashwith soap and water. The vinegar will neutralize the hardener and lesthes cehannces of longterm effects.Use goggles, a face shield, safety glasses or other items as required to prevent contact with the eyes. If material gets into the eyes, immediately flush with waterfoart least15 minutes andcallaphysician. Generally, kethee worpk ar ea as uncluttered and clean as possible, andclean up any minor spills immediatelyto preventaccidentsaklin contactata latertime. Keep tools clean and properly stored. Dispose of trash and empty containers properly.
Packaging & Availability
- Packaging Weights
Quart Gallon Pail ES6209 Part A 1.75 lb. 7.5 lb. 38 lb. Kit 3.5 lb. 15 lb. 76 lb.