Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Color
- Physical Properties
- Mechanical Properties
- Thermal Properties
- Electrical Properties
- Impact Properties
- Injection Molding
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵐ RTI for this grade is not measured and is based on grades with similar formulation ad performance.
- ᵒ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. Impact measured on natural color
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Density ¹¹ | 1.16 | g/cm³ | ISO 1183 |
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.15 | % | ISO 62-4 |
Moisture Absorption (at 23°C, 50% RH, Equilibrium) ¹¹ | 0.3 | % | ISO 62-4 |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.7 | % | ISO 62-1 |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.7 | % | ASTM D570 |
Water Absorption (at 23°C, saturated) ¹¹ | 3.5 | % | ISO 62-1 |
Water Absorption (at 23°C, saturated) ¹¹ | 3.5 | % | ASTM D570 |
Melt Volume Rate (at 250°C, 2.16 kg) ¹¹ | 5 | cm³/10 min | ISO 1133 |
Melt Volume Rate (at 250°C, 5 kg) ¹¹ | 15 | cm³/10 min | ISO 1133 |
Melt Volume Rate (at 260°C, 5.0 kg) ¹¹ | 23 | cm³/10 min | ISO 1133 |
Specific Gravity ¹¹ | 1.16 | — | ASTM D792 |
Melt Flow Rate (at 250°C, 5 kgf) ¹¹ | 15 | g/10 min | ASTM D1238 |
Mold Shrinkage (flow) ᵍ ¹¹ | 0.5 - 0.7 | % | SABIC method |
Mold Shrinkage (xflow) ᵍ ¹¹ | 0.6 - 0.8 | % | SABIC method |
Charpy impact (ISO 179, after Xenon-Arc weathering (ISO 4892-2), Resistance to UV light) ᵒ ¹¹ | Pass | — | IEC 60079-0 |
Value | Units | Test Method / Conditions | |
Tensile Modulus (at 1 mm/min) ¹¹ | 1750 | MPa | ISO 527 |
Tensile Stress (Yield, 50 mm/min) ¹¹ | 45 | MPa | ISO 527 |
Tensile Strain (Yield, 50 mm/min) ¹¹ | 5.5 | % | ISO 527 |
Tensile Strain (Break, 50 mm/min) ¹¹ | min. 60 | % | ISO 527 |
Tensile Nominal Strain (Break, 50 mm/min) ¹¹ | min. 60 | % | ISO 527 |
Flexural Modulus (at 2 mm/min) ¹¹ | 1825 | MPa | ISO 178 |
Flexural Strength (at 2 mm/min) ¹¹ | 70 | MPa | ISO 178 |
Tensile Modulus (at 50 mm/min) ¹¹ | 1750 | MPa | ASTM D638 |
Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 45 | MPa | ASTM D638 |
Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 5.5 | % | ASTM D638 |
Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | min. 60 | % | ASTM D638 |
Tensile Nominal Strain (Break, Type I, 50 mm/min) ¹¹ | min. 60 | % | ASTM D638 |
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 1900 | MPa | ASTM D790 |
Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 70 | MPa | ASTM D790 |
Ball Indentation Hardness (H358/30) ¹¹ | 78 | MPa | ISO 2039-1 |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 105 | °C | ISO 75/Af |
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 123 | °C | ISO 75/Bf |
Vicat Softening Temperature (Rate B/50) ¹¹ | 123 | °C | ISO 306 |
Vicat Softening Temperature (Rate B/50) ¹¹ | 123 | °C | ASTM D1525 |
Vicat Softening Temperature (Rate B/120) ¹¹ | 123 | °C | ISO 306 |
Vicat Softening Temperature (Rate B/120) ¹¹ | 123 | °C | ASTM D1525 |
Vicat Softening Temperature (Rate A/50) ¹¹ | 137 | °C | ISO 306 |
Vicat Softening Temperature (Rate A/120) ¹¹ | 138 | °C | ISO 306 |
Coefficient of Thermal Expansion (at 23°C to 50°C, flow) ¹¹ | 0.000085 | 1/°C | ISO 11359-2 |
Coefficient of Thermal Expansion (at 23°C to 50°C, flow) ¹¹ | 0.000085 | 1/°C | ASTM E831 |
Coefficient of Thermal Expansion (at 23°C to 50°C, xflow) ¹¹ | 0.00011 | 1/°C | ISO 11359-2 |
Coefficient of Thermal Expansion (at 23°C to 50°C, xflow) ¹¹ | 0.00011 | 1/°C | ASTM E831 |
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 105 | °C | ASTM D648 |
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 123 | °C | ASTM D648 |
Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
Temperature Index (Tensile Strength, 1.5 mm) ¹¹ | 108 | °C | IEC 60216 |
Temperature Index (Tensile Strength, 3 mm) ¹¹ | 108 | °C | IEC 60216 |
Value | Units | Test Method / Conditions | |
Comparative Tracking Index ¹¹ | 175 | V | IEC 60112 |
Surface Resistivity (ROA) ᵐ ¹¹ | 1000000000 - 100000000000 | Ω | IEC 60093 |
Static Decay (at 5000V to max. 50V) ¹¹ | max. 0.01 | Seconds | FTMS101B |
Dielectric Constant (at at 60-90 GHz) ¹¹ | 2.73 | — | - |
Dissipation Factor (at at 60-90 GHz) ¹¹ | 0.022 | — | - |
Surface Resistivity ᵐ ¹¹ | 1000000000 - 100000000000 | Ω | ASTM D257 |
Value | Units | Test Method / Conditions | |
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 60 | kJ/m² | ISO 180/1A |
Izod Impact (Notched, 80*10*3, at 23°C) ¹¹ | 65 | kJ/m² | ISO 180/1A |
Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 60 | kJ/m² | ISO 180/1A |
Izod Impact (Notched, 80*10*3, at -30°C) ¹¹ | 65 | kJ/m² | ISO 180/1A |
Izod Impact (Unnotched, 80*10*3, at 23°C) ¹¹ | No break | kJ/m² | ISO 180/1U |
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | No break | kJ/m² | ISO 180/1U |
Izod Impact (Unnotched, 80*10*3, at -30°C) ¹¹ | No break | kJ/m² | ISO 180/1U |
Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ | No break | kJ/m² | ISO 180/1U |
Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 60 | kJ/m² | ISO 179/1eA |
Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 60 | kJ/m² | ISO 179/1eA |
Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | No break | kJ/m² | ISO 179/1eU |
Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | No break | kJ/m² | ISO 179/1eU |
Multi-Axial Instrumented Impact Total Energy (at 23°C) ¹¹ | 65 | J | ISO 6603-2 |
Multi-Axial Instrumented Impact Energy (peak, at 23°C) ¹¹ | 55 | J | ISO 6603-2 |
Multi-Axial Instrumented Impact Total Energy (at -30°C) ¹¹ | 65 | J | ISO 6603-2 |
Multi-Axial Instrumented Impact Energy (peak, at -30°C) ¹¹ | 55 | J | ISO 6603-2 |
Izod Impact (Notched, at 23°C) ¹¹ | 850 | J/m | ASTM D256 |
Izod Impact (Notched, at -30°C) ¹¹ | 750 | J/m | ASTM D256 |
Izod Impact (Unnotched, at 23°C) ¹¹ | No break | J/m | ASTM D4812 |
Izod Impact (Unnotched, at -30°C) ¹¹ | No break | J/m | ASTM D4812 |
Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 40 | J | ASTM D3763 |
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 35 | J | ASTM D3763 |
Instrumented Dart Impact Peak Force (at 23°C) ¹¹ | 4000 | N | ASTM D3763 |
Instrumented Dart Impact Total Energy (at -30°C) ¹¹ | 40 | J | ASTM D3763 |
Instrumented Dart Impact Energy (Peak, at -30°C) ¹¹ | 35 | J | ASTM D3763 |
Instrumented Dart Impact Peak Force (at -30°C) ¹¹ | 4800 | N | ASTM D3763 |
Value | Units | Test Method / Conditions | |
Back Pressure ⁷ | 0.3 - 0.7 | MPa | — |
Drying Temperature ⁷ | 80 - 95 | °C | — |
Drying Time (Cumulative) ⁷ | 8 | Hrs | — |
Drying Time ⁷ | 2 - 4 | Hrs | — |
Front - Zone 3 Temperature ⁷ | 240 - 260 | °C | — |
Maximum Moisture Content ⁷ | 0.03 | % | — |
Melt Temperature ⁷ | 240 - 260 | °C | — |
Middle - Zone 2 Temperature ⁷ | 230 - 250 | °C | — |
Mold Temperature ⁷ | 50 - 90 | °C | — |
Nozzle Temperature ⁷ | 240 - 260 | °C | — |
Rear - Zone 1 Temperature ⁷ | 220 - 240 | °C | — |
Screw Speed (Circumferential speed) ⁷ | 0.15 - 0.2 | m/s | — |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Comparison of LNP STAT-KON DD000XI And STAT-LOY D3000IEU6 to Traditional Plastic Compounds
Property Standard Unit STAT -LOY™ D3000IEU6 Alloy Typical Conductive GF-PA6 Alloy Typical Conductive PC Alloy STAT-KON™ DD00XI Compound Typical Conductive PC Compound FARADEX™ DS0036l Compound LEXAN™ WXL1414 Resin
Flexural Modulus ISO178 MPa 1825 - 2050 2300 2890 2600 2250 Flexural Strength ISO178 MPa 70 - 79 90 100 80 85 Tensile Modulus ISO527 MPa 1750 7700 1725 2500 2600 2800 2150 Tensile Strength ISO 527 MPa 45 105 50 45 60 55 60 Elongation to Break ISO 527 % >60 6 >10 10 4 - - IZOD-notch at 23°C ISO180/1A kJ/m² 60 14 70 24 6 14 70 IZOD-notch at -30°C IS0179 kJ/m² 60 - - 10 - - 60 HDT 0.45 MPa ISO 75 °C 123 217 128 139 138 136 140 HDT 1.8 MPa ISO 75 °C 105 196 113 129 127 125 128 Density ISO 1183 g/cm³ 1.16 1.38 1.18 1.21 1.24 1.29 1.19 Moisture absorption ISO 62 % 0.15 - 0.3 ~2 - 0.06 - 0.12 0.06 - 0.12 0.13 0.15 Shrinkage x-flow ISO294-4 % 0.6 - 0.8 0.4 - 0.8 0.6 - 0.9 0.6 - 1.0 0.6 - 1.0 0.4-06 0.4 - 0.8 Surface resistivity ASTM 257D Ω 1.00E+09 1.00E+11 1.00E+11 1.0E+6-
1.00E+101.E+02-
1.00E+061.00E+03 1.00E+15
Packaging & Availability
- Country Availability
- Regional Availability