Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
- Performance
- Excellent Flame Retardancy, BS476: Part 7:1997 Class I rating
- Excellent corrosion resistance to acidic and alkaline environment
- High strength characteristics
- Excellent impact strength and toughness
- Fast wet-out. Low drainage
Applications & Uses
- Markets
- Applications
- Cure Method
- Plastics & Elastomers Processing Methods
- Suggested Uses
SIROPOL 992 FRA can be used for corrosion resistant, reinforced thermosetting plastic equipment including filament wound, hand lay-up and spray-up tanks, pipes ducts, stacks, scrubbers, lining or other equipment handling corrosive gasses, vapors or liquids where a high degree of flame retardancy is required.
Properties
- Flame Rating
- Physical Form
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Percent Solids | 60 ± 2 | % | — |
| Viscosity Brookfield, cps spindle 2 at 30 rpm | 450- 500 | cps | — |
| Pounds per Gallon | 9.7 | — | — |
| Flash Point Range | 23 - 37 | °C | — |
| Barcol Hardness | 35 | psi | ASTM D-2583 |
| Tensile Strength | 12700 | psi | ASTM D-638 |
| Tensile Modulus (x 10^5) | 3.5 | psi | ASTM D-638 |
| Tensile Elongation at yield | 3.4 | % | ASTM D-638 |
| Tensile Elongation at break | 3.5 | % | ASTM D-638 |
| Flexural Strength | 22100 | psi | ASTM D-790 |
| Flexural Modulus (x 10^5) | 7.4 | psi | ASTM D-790 |
| Heat Distortion Temperature | 92.5 | °C | ASTM D-648 |
Regulatory & Compliance
- Quality Standards
- Dot Label Required
Flammable Liquid
Technical Details & Test Data
- Typical Curing Characteristics
SPI Gel Time – 82 °C Bath, 2 % Luperco ATC paste
Temperature °C Gel Time minutes Peak Exothermic Total Time minutes 82 17 193 °C 20 TYPICAL MEKP CURING CHARACTERISTICS:
Gel Time @ 25 °C Bath, (0.3% Co 6% + 0.5% DMA 10% + 1.25% M-50)
- Gel Time, Minutes 20 - 25
- Total time: 30 - 40
CAUTION: Thoroughly mix promoters with resin before adding catalyst.
- Typical Flame Retardancy of Laminates
Resin BS476:Part 7 Flame Spread Class Siropol 992 FRA
With 3 % antimony trioxide
75 I
Packaging & Availability
- Standard Packaging
205 Kgs Standard Steel non returnable Drums
Storage & Handling
- Handling
SIROPOL 992 FRA resin contains ingredients, which could be harmful if mishandled. Contact with skin and eyes should be avoided and necessary protective equipment and clothing should be worn.
Saudi Industrial Resins Ltd., maintains Material Safety Data Sheets on all of its products. Material Safety Data Sheets contain health and safety information for your development of appropriate product handling procedures to protect your employees and customers.
OUR MSDS: should be read and understood by all of your supervisory personnel and employees before using SIR`s products in your facilities.
- Recommended Storage
DRUMS:- Store at temperatures below 25°C. Storage life decreases with increasing storage temperature. Avoid exposure to heat sources, such as direct sunlight or steam pipes. Keep containers sealed to prevent moisture pickup and monomer loss. Rotate stock.
BULK: - Store in stainless steel tanks or tanks lined with epoxy or phenolic coatings. Observe precautions against heat and moisture (see above). An oxygen or dry air spurge may be desirable to keep inhibitors activated. Store at temperature below 25 °C.