Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Applications
Indoors and outdoors on steel, aluminum, pickled zinc, electrogalvanized, earthenware*, bare or coated with old adhering paints in good condition. Indoors only, on concrete, cement and hydraulic coatings (pH <9), plaster and derivatives, plaster tiles, sanded melamine, wood and derivatives, PVC and copper.
- Classification
AFNOR NF T 36-005 Family I Class 4a
Features & Benefits
- Ready-to-Use Product Features
- Features
- Quick drying and covering with all one-component acrylic or alkyd paints in solution or emulsion.
- Microporous.
- Fine grain, covered with stretched lacquer finishes.
- Rust protection.
- Opacifiante.
- Available in the color of the finish, it significantly improves the opacity of the finish system (bright shades).
- If the hanging function is required, prefer ADERPRIM MICRO in white or pastel shades.
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Application Characteristics
Conditions Application: Interior: ambient and substrate temperature between 8° and 35°C - Hygrometry < 70% RH. Do not apply on condensing substrates. Exterior: ambient and surface temperature between 5° and 35°C - Hygrometry < 80% RH. Substrate temperature at least 3°C above dew point; avoid surfaces that are frozen, damp or too hot, do not apply in rainy, foggy weather, in strong winds or in direct sunlight. In general, moisture content of masonry < 5%.
Application material: Sleeve: woven polyester from 5 to 13mm depending on the destination Airless: low pressure nozzle 517 at 100-120 bars after dilution of 5% white spirit Brush: mixed.
Dilution: Ready to use, up to 5% white spirit.
- Implementation
In general, after preparation, the substrates must be healthy, cohesive, clean and dry to receive a coat of ADERPRIM MICRO before applying two compatible finishing coats or applying a coating or glass cloth. to paint. - Hardwoods (Doussié, Niangon, Teak): preparation of the support, in particular by degreasing with DAF 310, then application of a layer of
Indoors and outdoors On metals such as: - Nonoxidized ferrous metals, electrogalvanized: preparation of the support, in particular by degreasing with DAF 310 then application of a layer of ADERPRIM MICRO. The supports must comply with the DTU concerning them and in particular with NF DTU 59.1. Uncoated plaster tiles, preparation of the support then application of a coat of ADERPRIM MICRO. Prior recognition necessary to determine the most suitable preparation for their condition and nature (cleaning, washing/rinsing, sanding, scraping, degreasing, roughening, dusting, etc.).
On new wood such as:
- Soft wood (Framiré, Okoumé, Poplar, Pine, Pichpin): preparation of the support, in particular by eliminating resin drips, then application of a coat of
ADERPRIM MICRO.
- Slightly oxidized ferrous metals: in addition to the preparations mentioned above, cleaning/scraping of the corroded parts before applying a coat of BLOC RUST on the rusty parts, then applying a coat of ADERPRIM MICRO. On old adherent single-component paints or varnishes: preparation of the support, in particular by degreasing with DAF 310 and roughening of glossy paints and varnishes, then application of a coat of ADERPRIM MICRO.
Indoors On substrates such as: - Cement, hydraulic coatings and concrete with pH <9, cardboard plasterboard, paint coatings, sanded melamine: preparation of the substrate then application of a layer of ADERPRIM MICRO - PVC, copper, earthenware preparation of the substrate, in particular by degreasing with DAF 310 then application of a coat of ADERPRIM MICRO.
- Hard woods with tannins (oak, chestnut): preparation of the support then application of a coat of ADERPRIM MICRO. ADERPRIM MICRO.
- Aluminum, zinc: preparation of the support, in particular by degreasing with DAF 310 then pickling with SOLUTION NT 330 followed by rinsing with
water, drying then application of a layer of ADERPRIM MICRO. On other supports such as stainless steel, galvanized steel, polycarbonate, exterior PVC, glass, porcelain stoneware, cement plaster and fresh concrete (pH>9), wood containing antioxidants (iroko, padouk, etc.) which would prevent drying , consult the technical data sheets for primers of the AQUAPRIM MICRO type or of the PROTEC range or contact our technical departments.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Dry Extract | 76.0 | % | — |
| Volume | 54.0 | — | — |
| Yield | 13 - 15 | m2/L | — |
| VOC of this product | max. 500 | g/L | — |
| VOC limit value | max. 410 | g/L | — |
Technical Details & Test Data
- Technical Characteristics
Binders: Solvent-borne urethane alkyd
Movie Look: Velvety matte, taut
Specular Brilliants: less than 4% at 60° angle, less than 7% at 85° angle
Shades: White and all shades of the Microcolor Evo system, i.e. more than 105,000 shades (Series A, B, C).
Packaging & Availability
- Availability
Available in 0.75L, 3L, 12L.
Storage & Handling
- Storage
Storage before opening: 12 months in the original sealed container, protected from frost and high temperatures >35°.
Storage after opening: Close the container well after opening in order to preserve the characteristics of the product.