Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- FEATURES
- Superior color stability and gloss retention compared to aromatic elastomers.
- Outstanding abrasion resistance.
- Extended gel time for better flow-out providing a smooth more uniform finish.
- Forms monolithic membrane that can be handled and walked on within two minutes or less from the time it’s sprayed.
- 100% solid, no solvents, and zero VOCs.
- High build up to any thickness in one application.
- High dry temperature stability to 200°F (93°C) withintermittent temperatures to 250°F (121°C).
- Compliant with FDA/USDA for incidental food contact.
Applications & Uses
- Applications
- Application Method
- RECOMMENDED USES
- Urethane foam roofing.
- Topcoat
- Water features.
- Tanks, pond, and lagoon containment lining.
- Walls, ceilings for meat, dairy processing plants.
- Aquatic animal, water ride basins, and animal habitats.
- Exposed signs and displays.
- Truck beds and undercarriage liners .
- EIFS base coat replacement.
- Encapsulation of structural steel to protect and retard rust formation.
- Encapsulation of lead, low level radioactivity, and asbestos contaminated surfaces.
- GENERAL APPLICATION INSTRUCTIONS
Apply AMP™ 100 only to clean, dry, sound, surfaces free of loose particles or other foreign matter. AMP™ 100 canbe sprayed over a broad range of ambient and substrate temperatures. It is recommended that AMP™ 100 be sprayed in multi-directional (north/south - east/west) passes to ensure uniform thickness.
STEEL: 4-5 mil anchor profile is best for maximum adhesion andvaries per application and conditions; adhere to proper SSPC standards.
NON-FERROUS METALS: Prepare surface in accordance toSSPC-SP16 (Brush-off Blast Cleaning of Non-Ferrous Metals),It is imparative that the user perform their own adhesion tests.
WOOD: Apply polyurea onto a clean, dry, and sanded surface; free from burrs, splinters and loose debris. (It is recommended to prime wood and other porous surfaces before application of heated, fast-set polyureas to reduce pin holing).
CONCRETE: Prepare concrete in accordance with SSPC/NACE Standards and SPI Concrete Prep Guide.
PREVIOUSLY APPLIED COATINGS: SPI recommends UB™(ULTRA BOND™) products over existing coatings that are pastthe recoat window and/or application over other coatings. The use of SPI Prep Wipe™ solution will tack up the existing polyurea coating and can help promote bonding of the AMP™ 100.
Properties
- Typical Properties
- Wet Properties
| Value | Units | Test Method / Conditions | |
| Tensile Strength | min. 3,200 (22) | psi (MPa) | ASTM D412-06a |
| Hardness | 91 - 101 | Shore A | ASTM D2240 |
| Hardness | 48 - 58 | Shore D | ASTM D2240 |
| Elongation | min. 375 | % | ASTM D412-06a |
| 100% Modulus | 1,100 ± 100 (8) | psi (MPa) | ASTM D412-06 |
| 300% Modulus | 1,738 ± 100 (12) | psi (MPa) | ASTM D412-06 |
| Tear Resistance (91 KN/m) | 519 PLI ± 50 | - | ASTM D624 |
| Exposure Temperature | -50 - +200 (-45 - +93) | °F (°C) | - |
| Value | Units | Test Method / Conditions | |
| Solids by Volume | 100 | % | - |
| Solids by Weight | 100 | % | - |
| Volatile Organic Compounds (0 g/l) | 0 | lbs./gal. | - |
| Theoretical Coverage DFT (16 mils/gal) | 100 | sq. ft. | - |
| Weight per gallon (approx.) | 8.8 (4.0) | lbs. (kg) | - |
| Number of Coats | 1 - 2 | - | - |
| Mix Ratio | 1 “A” : 1 “B” | - | - |
| Viscosity (77°F, 25°C, A, B) | 1,350 ± 50 (450 ± 50) | mPa.s | - |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Applications & Uses
Thoroughly agitate the “B” components of this product prior to application. Use a SPI folding blade mixer, or equivalent equipment approved by SPI. Install mixer through the extra2” bung hole provided on all “B” drums. Care must be taken not to cross contaminate the individual components with the mixing equipment; for best mixing results, supply the SPI mixer with 25 cfm of air at 100 psi. Thinning is not required. Using any thinner may adversely affect product performance.
- PROCESSING EQUIPMENT & SETTINGS
MACHINES: GRACO
(Gusmer, Glasscraft)A-25*
A-XP1
E-10 HP
E-20*
E-30*
E-XP1
E-XP2
H-20/35 Pro
H-25*
H3500
H-40*H-50*
HV-20/35
H-XP2
H-XP3
Reactor2 E-XP2
Reactor2 H-XP2
Reactor2 H-XP3
Reactor2 E-30*
Reactor2 H-30*
Reactor2 H-40*
Reactor2 H-50*PMC GH-25*
GH-40*
PA-25*
PAX-25
PH-2*
PH-25*PH-40*
PHX-2
PHX-25
PHX-40
PMCA-20SPRAY FOAM
EQUIP & MFG5/12K*
6/6K*6/12K *2,000 psi machines GUNS: GRACO
(Gusmer, Glasscraft)Fusion AP
Fusion MP
GAP Pro
GX7-DI
GX-8 ProGX7-400
P2
P2 Elite
P2 Elite “C”
D7PMC AP-2 SPRAY FOAM
EQUIP & MFGBoss - Standard 1:1 ratio, heated, plural-component equipment developing a minimum of 1700 psi (11.72 MPa) dynamic pressure at the gun with heating capabilities to 170°F(77°C) will adequately spray AMP™ 100.
- Machines capable of producing a higher dynamic psimay be required depending on the service environmentthe AMP™ 100 will be exposed to.
- Proportioning machine primary heater temperature 160-170°F (71-77°C).
- Hose temperature 160-170°F (71-76°C). A hose thermometer inserted under the insulation near the gun should read a minimum of 145-155°F (63-68°C).
- Physical properties will be enhanced when sprayedat higher pressure (3000 psi or more); and utilizing an impingement mix gun such as MP Fusion or GX7-DI gun.
- Do not use mixing chambers with output greater than1.5 gallons per minute.
- LIMITATIONS
- AMP™ 100 is for professional use only. User must be proficient in the application of AMP™ 100 and the use of the high pressure heated plural component equipment used to apply it.
- AMP™ 100 must be stored at temperatures between 60—90°F (15—32°C).
- Liquid temperature in containers/drums during application 70—100°F (21—38°C).
- Apply AMP™ 100 when surface and air temperatures are above 40°F (5°C) and the surface temperature is at least 5°F (3°C) above dew point and rising.
- Minimum material/container temperature for spray application is 70°F (21°C).
- Avoid moisture contamination in containers. Containers should not be resealed if contamination is suspected.CO2 created pressure can develop. Do not attempt to use contaminated material.
- Undried air exposed to liquid components will reduce physical properties of the cured coating.
Note: The material supplied is a two component system(component “A”/component “B”, which is used to formulatethis product. The quality and characteristics of the finishedpolymer is determined by the mixture and application of thetwo components by the person applying the polymers.
- CURING SCHEDULE
Gel ± 6 sec. Tack Free ± 10 sec. Post Cure*** 24 hour Recoat 0 - 12 hours *-All cured film properties are approximate since processing parameters, ad-mixture types, and quantities change physical properties of the cured elastomer. Elevated temperatures will accelerate the curing process and shorten the re-coat window.
** Test performed in a dry, static environment.
*** Complete polymerization to achieve final strength can take upto several days or weeks, depending on a variety of conditions orproduct type. All samples for above tests were force cured 48hours or aged for more than three weeks. It is recommended that the user perform their own independent testing.The samples for tests were sprayed with Graco HXP3 @ 2,800psi (19 MPa) dynamic pressure at the gun. Proportioning machine primary heater and hose heat 170°F (77°C) Graco MP Fusion gunwith 29/29 mixing chamber with .040 ceramtip.TEST INFORMATION Abrasion Resistance
ASTM D4060
1000 g - 1000 cyclesH-18 20.5 mg loss H-10 33 mg loss H-22 46.4 mg loss CS-17 19.1 mg loss Weatherability (black)
3000 hours (QUV)no evidence of failure
Packaging & Availability
- Packaging Type
- COLORS
AMP™ 100 is available in SPI standard colors (Sand, MediumGrey, and Black).
Note: AMP™ 100 is an aliphatic polyurea. Therefore, withcontinuous full-light exposure, white or very light colors will yellow over a period of time. Color change and superficialoxidation will occur. SPI urethane, polyaspartics, and othersuitable topcoats can be used where long-term colorstability and increased longevity in full sun exposure are ofcritical importance.- PACKAGING
This product is sold in standard 110 gallon drum and 550 gallon tote sets. Available in other container sizes.
Storage & Handling
- Shelf Life
- 6 Months