Tasnee PP H3030 - HPP - Extrusion

Knowde Enhanced TDS

Identification & Functionality

Features & Benefits

Labeling Claims: Food Contact Acceptable
Materials Features: Excellent Transparency Properties,
Food Contact Acceptable,
Good Processability,
High Gloss,
High Stiffness

Applications & Uses

Markets: Adhesives & Sealants,
Personal Care,
Printing & Packaging
Applications: Printing & Packaging — Packaging
Food & Beverage Packaging,
Industrial & Transport Packaging,
Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
Applicators & Accessories
Adhesives & Sealants — Packaging & Paper
Tape & Label Adhesives
Printing & Packaging — Tapes, Labels & Adhesives
Tapes & Labels
Plastics & Elastomers End Uses: Biaxially Oriented Film,
Film,
Flexible Packaging,
Food Packaging,
General Purpose,
Heavy Duty Bags,
Labels,
Oriented Film,
Shrink Wrap,
Tape
Plastics & Elastomers Processing Methods: Extrusion
Typical Applications: Films produced with TASNEE PP H3030 are suitable for various printing, lamination and coating processes for food and non-food packaging applications. Food packaging: biscuits, chocolates, confectionaries, chips, baked foods, pasta, snack foods, pet foods etc. Non-food packaging: soaps, detergents, textile bags, self-adhesive tapes, wrap around, self-adhesive labels etc.

Properties

Color: Translucent,
White
Physical Form: Pellets,
Solid
Mechanical Properties
Physical Properties
Typical Processing Conditions: Extrusion Temperature 200 ~ 250°C

Chill Roll Temperature 20 ~ 40°C

MD Stretching Temperature 130 ~ 160°C

MD Stretching Ratio 4 ~ 7

TD Stretching Temperature 155 ~ 170°C

TD Stretching Ratio 7 ~ 10

Note: Processing parameters should only be used as guidelines. The above properties values are not to be construed as specifications.

	Value	Units	Test Method / Conditions
Charpy Notched Impact Strength (at 23°C)	4	kJ/m2	ISO 179/1eA
Flexural Modulus (1% Secant)	1450	MPa	ISO 178
Rockwell Hardness	100	R	ISO 2039-2
Tensile Elongation at Yield	10	%	ISO 527-2
Tensile Strength at Yield	33	MPa	ISO 527-2

	Value	Units	Test Method / Conditions
Density	0.9	g/cm3	ISO 1183
Heat Distortion Temperature (at 0.45 MPa)	102	°C	ISO 75-2
Melt Flow Rate (230°C / 2.16 kg)	3	g / 10 min	ISO 1133
Melting Temperature	163	°C	ISO 11357-3
Vicat Softening Temperature	154	°C	ISO 306

Regulatory & Compliance

Food Contact: The material is manufactured to the highest standards but, special requirements apply to certain applications, such as food contact end-use. For specific information on regulatory compliance, please contact TASNEE below or our local representative in your area.

Safety & Health

Safety: Workers should be protected from the possibility of skin or eye contact with molten polymer. As minimum precaution, safety glasses and heat resistance gloves are suggested to prevent mechanical or thermal injury to eyes and hands. Molten polymer exceeding processing condition requirements may degrade and release, fumes, vapors and unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes and vapors. Legislation on the control of emissions and pollution prevention must be observed. If the principles of sound manufacturing practice are adhered to and the place of work is well ventilated, no health hazards are involved in processing the material. The material may burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. In burning the material generates considerable heat and may release a dense black smoke. Fires should be extinguished by heavy foams or dry powder. For further information about safety in handling and processing please refer to the Material Safety Data Sheet (MSDS).

Packaging & Availability

Storage & Handling

Storage: The material is packed in 25 kg bags or in bulk containers protecting it from contamination. Storage time of material longer than 6 months may have a negative influence on the quality of the final product. It is generally recommended to convert all materials latest within 6 months from delivery date. The material is subjected to degradation by ultra-violet radiation or by high storage temperatures. Therefore the material must be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during storage. Further unfavorable storage conditions are large fluctuations in ambient temperature and high atmospheric humidity. TASNEE will not give any warranty to unfavorable storage conditions which may lead to quality deterioration such as color change, bad smell and inferior product performance.