Products

Magnapur® MGP-N2SC is a stearic acid coated, magnesium hydroxide of natural origin (brucite). This 2.0 µm coated magnesium hydroxide is suitable as a flame retardant in in a wide range of applications including wire & cable bedding and jacketing, foams, hoses, roofing, sheet, and profile.

provides a cost-effective way to flame retard and smoke suppress plastics, rubber and other polymer systems. It is alumina trihydrate and has good flowability and wetout. H-TEC™ 1000 is used for flexible and rigid PVC, nitrile rubbers, neoprene, polyolefins, EPDM, SBR, EPR, latexes, urethanes, EVA copolymers, unsaturated polyesters and other polymer systems.

Marshall Additive Technologies FD409 is a reactive synergist blend specially formulated to provide a good balance of flame retardant performance and reduced cost when used as a partial Antimony Trioxide replacement. This product is applicable to PVC, CPE, and a wide range of polymer systems where the flame retardant is bromine or chlorine based. Depending on the specific formulation, it is typically possible to replace between 30 and 50% of Antimony Trioxide.

Marshall Additive Technologies FD335 is a reactive synergist blend specially formulated to provide the maximum flame retardant performance when used as an Antimony Trioxide replacement. This product is applicable to PVC, CPE, and a wide range of polymer systems where the flame retardant is bromine or chlorine based. Depending on the specific formulation, it is typically possible to replace between 50 and 100% of Antimony Trioxide.

Marshall Additive Technologies SDAOM 100% Ammonium Octamolybdate smoke suppressant.

HT1000 is a Fine ATH is used in Wire/Cable (Insulation/Sheathing), PVC/NBR Foam.

A208 is a Ground ATH is used in BMC, Carpet Backing, Rubber.

Maxfil® MX104 is a High Loading ATH is used in Highly Filled Resin System.

AH255 is a Coarse Ground ATH is used in Composites.

A202 is a Fine Ground ATH is used in Adhesives, Sealants, Electrical, PVC.

Maxfil® MX200 is a High Loading ATH is used in Highly Filled Resin System.

AH290 is a Ground ATH is used in Yarn, Mills, SMC.

Marshall Additive Technologies SD890 is a reactive smoke suppressant blend specially formulated to provide the maximum reduction in smoke generation at the lowest possible cost when replacing molybdate based additives in PVC compounds. Specifically, work has been done which shows that it is possible to replace 100% of Ammonium Octamolybdate while achieving a further improvement in smoke suppression of a typical PVC plenum jacketing formulation and small gain in flame retardancy.

Maxfil® MX100 is a High Loading ATH is used in Highly Filled Resin System.

Marshall Additive Technologies FDAO 100% antimony trioxide synergist for halogenated flame retardant systems.

C-TEC™ CTZB400 is typically used as a formulating additive to increase char strength, reduce smoke, and to provide afterglow suppression.

A204 is a Fine Ground ATH is used in Vinyl, SMC, PVC, Pultrusion.

Marshall Additive Technologies FD440 is an antimony free inorganic synergist for halogenated flame retardant systems. FD440 can allow the formulator to significantly reduce the antimony trioxide level in a formula while providing equivalent performance at a reduced cost. This product is applicable to PVC, CPE, and a wide range of polymer systems where the flame retardant is bromine or chlorine based.

A212 is a Ground ATH is used in SMC, BMC.

A206 is a Ground ATH is used in Pultrusion, BMC.

Marshall Additive Technologies FSD479 is an antimony free proprietary inorganic blend flame retardant synergist for use with halogen based flame retardant polymer compounds where Zinc Hydroxy Stannate is used as the primary synergist. It allows the formulator to reduce the amount of the expensive Zinc Hydroxy Stannate while retaining flammability performance and hence provide an overall cost saving. This product is applicable to PVC, CPE, and a wide range of polymer systems where the flame retardant is bromine or chlorine based.

AH330 is a Ground ATH is used in Electronics, Glassware, Spray Up.

AH430 is a Ground ATH is used in BMC, FRP, Pultrusion.

AH280 is a Ground ATH is used in Mass Transit, Carpet Backing.

AH270 is a Coarse Ground ATH is used in Latex, Foam, Neoprene.

A210 is a Ground ATH is used in SMC, BMC.