Products in Other Electrical & Electronics Applications

PA6 Glass fiber 60% reinforced

ROTEC® ABS 1002 FR V0/5 is ABS, injection molding grade, transparent, waterclear.

PROFLEX T4-11 is a styrene-butadiene-styrene material for injection molding.

POLYKING® PET Thermoplastic polyester is with very high mechanical property, heat resistance, good electrical properties, excellent chemical resistance and oil resistance. The molding part is dimensional stable and excellent surface appearance etc. It is widely used in electrical and electronic, mechanical and automotive fields.

MDS Lubricant Suppliers FF103B - Multilube Bulk is a highly effective blend of penetrating and lubricating fluids, water dispersing agents and corrosion inhibitors. Specifically developed to lubricate and release parts which are corroded and/or seized. Instantly displaces all water from damp or wet components. Penetrates deeply to prevent moisture traps. Leaves a protective film to waterproof and guard against corrosion. Lubricates - increases efficiency of working parts. FF103B Multi-Lube may be used as a very effective solvent cleaner/ degreaser and to break down residual deposits of old lubricants. Use on all ignition systems, electrical, electronic and engineering components including – electric motors, generators, relays, coils, switches, terminals, telephonic and general communication equipment, tools and machinery, motor cars, general transport, boats etc. highly recommended for Off shore oil and marine applications. This product contains no nut derived, genetically modified, soya, animal derived or vegetable derived ingredients.

Cel-Span® CFA 800 is an endothermic foaming agent concentrate recommended for injection molding & extrusion applications for a variety of thermoplastic resins such as polyethylene, polypropylene, styrenics, MPPO and ABS. Cel-Span® CFA 800 is recommended for extrusion, and structural foam molding of polyolefins, polystyrene, MPPO and ABS. This product exhibits a very fine cell structure compared to a typical endothermic foaming agent in extrusion applications. This product has been engineered to eliminate splay and to exhibit good surface esthetics for solid injection foam parts.

PERGAPROP HX-10 PP is 2,5-Dimethyl-2,5-di-(tert-butylperoxy)-hexane 10%, Granules with Polypropylen.PERGAPROP HX-10 PP is used for the production of controlled rheology polypropylene (CR-PP).

INOFLON® GN7001 has high dielectric strength with good dimensional stability.

A208 is a Ground ATH is used in BMC, Carpet Backing, Rubber.

PA6 glass fiber 20% reinforced V-0

CompaDur® 121 GK 30 (009) is a PBT, injection molding grade, 30% glass beads, heat stabilized, low warp, good surface.

Changzhou Juyou New Material Technology JY201-50 has a strong shearing resistance, good transmission of light low surface tension , excellent water repellency and moisture resistant and low volatilitioon.

AO 1098 is a nonpolluting nontoxic Antioxidant with good heat‐resisting and water‐extracting performance. Widely applied to polyolefine, polyamide, polyester, polyvinyl chloride, ABS resin and petroleum product, often used with DLTP for promoting the antioxidative effect.

Astra Polymers Black-MB/P-Type is used under automotive, consumers, packaging, electrical, appliances, construction, agriculture.

Aptek® 2313-Pmf is a one component, premixed-frozen, silver-filled, electrically conductive polymer paste adhesive. It is designed to bond many dissimilar substrates and dissipate device generated heat. Aptek® 2313-Pmf is a 100% solids, solvent free system that will not form voids during cure or outgas after being fully cured. Aptek® 2313-Pmf has excellent reversion resistance and physical stability when subjected to high heat and humidity environments. This system displays higher ionic purity than epoxy systems minimizing the possibility of corrosion on components and circuitry. Aptek® 2313-Pmf Premixed-frozen, snap-cure, electrically conductive, adhesive

Titacon® GF520 20％GLASS FIBER REINFORCED, HIGH STRENGTH/STIFFNESS, HOMO-POLYACETAL.

Resiten® G10FR4 laminates are extremely durable, lightweight, and moisture resistant. they are available in sheet, strip, block, and fabricated parts.Applications are Military Service and Industrial Applications.

CLR1331 is a low stress, extremely tough casting compound which was developed for casting low voltage bushings and insulators.

Birch Plastics BirCom AM05 is the active antimicrobial ingredients prevent it from growing, producing energy, replicating or inhibiting any further growth. BirCom AM05 antimicrobial does not wear off or leach out over time and provides long-lasting and effective product protection from microbes.

Stellarchem AB870EM TPE Compound is shear dependent and can be processed on conventional thermoplastics equipment for injection molding or extrusion. It's a soft, elastomeric polyolefin based, completely recyclable, colorable & non-hygroscopic thermoplastics elastomer material.

PA 6 unfilled V-0

E-SPHERES® ES150 are General Purpose Fine Grade Standard Hollow Ceramic Microspheres.

ROMILOY® 6040 E UV is PC/ASA, injection molding grade, high-impact, good UV resistance, high heat resistance.

Sitradur® TF20 / C94150 is a polybutylene terephthalate (PBT) material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding.

CarbonX® XR-1 is delivered in pelletized powder form in 20kg PP bags. For bulk orders, CarbonX® can be delivered in 1000 kg FIBCs and also available in masterbatch form for thermoplastics and elastomers. Masterbatches have been optimally mixed to ensure the highest quality possible in the final product while cutting down on lead times for R&D and Production.

avanION 510 is a material widely used in industry in both rigid and foamed applications. The final density obtained as well as the type of polyol play a crucial factor in the antistatic characteristics of the system. avanzare has developed a variety of products that, depending on the type of application and foam structure, can be used as the main and unique antistatic agent or as synergistic with other products on the market.

RIKARESIN BPO-20E is used in the fields of adhesives, paints and electricity to improve toughness, flexibility and adhesion. Liquid epoxy resin with bisphenol A skeleton. Since it has excellent impregnation properties, it is also used for FRP molding and casting. Improves heat cycle property, thermal shock resistance and shock resistance.

MAYRON® MW3620 U is Polycarbonate (PC) grade product.

Iron Oxide Red HM101 is reddish in color having globular particle shape.

ElectriPlast® EP-CF/PC is Polycarbonate with Nickel Plated Carbon Fiber as core fiber.

Vibrant Colortech Black Universal VB 9036-E is based on PE, PP, ABS, EVA and other base polymers. The product range comprises specially selected carbon blacks for high jetness, food contact approval and for better dispersion.

Armlen PP-1EX is a frost resistant polypropylene. Designed for injection molding and extrusion of various items and parts for construction, electrical tools, machine engineering, household appliances, transportation and etc. Available in black color.

Morplas® Red 49(45-413) is dye line, which has good heat stability and is ideal for a wide range of plastics applications. Dyes can be combined with the plastic resin before to processing or added to the plastic during the process. They are soluble in various polymers at diverse amounts and have no effect on the basic characteristics of the underlying resin.

Otsuka Chemical ADVN is used at Low-temperature polymerization application. Technology in fabrics, resins, paints and adhesives is supported by catalyst chemistry in polymer chemistry. Otsuka Chemical contributes polymer industries by introducing variety of AZO type initiators in order to meet request from polymer industry with our technology.

Johoku Chemical JP-310 is a antioxidant, heat resistance stabilizer, non-discoloring stabilizer for plastics, lubricants.