Brands in Refining & Gas Processing

Ketron® PEEK grades offer chemical and hydrolysis resistance similar to PPS, but can operate at higher temperature range. PEEK 1000 offers steam and wear resistance, while carbon-reinforced PEEK provides excellent wear capabilities. Our latest grade, PEEK HPV, offers outstanding bearing performance. PEEK can be used continuously to 480°F (250°C) and in hot water or steam without permanent loss in physical properties. For hostile environments, PEEK is a high strength alternative to fluoropolymers. PEEK carries a V-O flammability rating and exhibits very low smoke and toxic gas emission when exposed to flame. Excellent chemical resistance Very low moisture absorption Inherently good wear and abrasion resistance Unaffected by continuous exposure to hot water or steam

MERICAT™ technology from Merichem® has been successfully used in gasoline/naphtha, condensate and crude oil streams for the sweetening of mercaptan compounds. With our proprietary FIBER FILM® Contactor as the mass transfer device, MERICAT™ uses caustic/catalyst/air as treating reagents.

SILFOAM® is WACKER’s innovative brand for smart foam control products. It covers silicone-based integrated system solutions for regulatingfoam-intensive applications, and thereby optimizing processes and end products. SILFOAM® foam-control systems are the result of a continuous process of applied R&D. SILFOAM® is carefully tested for its compatibility and effectiveness in the customer's formulations, thereby avoiding overfoaming in advance.

KRAIBURG continually tries to set new standards in technology, quality, manufacturing, delivery performance, customer relations and service. Highly customized and cost-effective solutions far exceed the current standards. KRAIBURG is the leading specialist for the development and manufacture of rubber and silicone compounds that fulfill the most stringent requirements.

Fibertec's wollastonite products come in powder and fibrous grades. Powder grades tend to be used as fillers in coatings, adhesives, sealants and paints. It is an inert material with an alkaline pH that improves toughness, weather resistance and moisture absorption. Powders, while having some aspect ratio, all tend to be -325 mesh. Fiber grades have a diameter ranging from 5 to 15 microns and aspect ratios from 15 to 20. They are most commonly used as a lower cost, lower performance replacement for milled fibers in composites. They are compatible with all resins and may be surface treated. Fibertec wollastonites are acicular (needle-like) mineral products milled to various morphologies and bulk densities. These products can be surface treated to enhance performance in thermoset and thermoplastic resins. Fibertec wollastonite is used as functional fillers and reinforcements in composites (thermosets) and compounds (thermoplastics) to increase mechanical properties (tensile, flexural, impact), minimize distortion at elevated temperatures, improve dimensional stability, and provide low moisture absorption.

GasDry natural gas desiccants are the highest-quality absorbent deliquescent available on the market. Van Gas Technologies produces three grades of desiccant for a wide variety of natural gas dehydration applications.

DithiaZolv™ is a concentrated mixture of proprietary and powerful surfactants specifically formulated to breakdown and dissolve dithiazine solids formed when triazine based H2S scavengers are used in oil and gas operations. Dissolving these solids into a water based slurry allows for easy final rinsing and cleaning. DithiaZolvTM helps optimize flow performance in pipelines, valves, filters, tanks and related process equipment.

Silica-alumina hydrates (SIRAL) exhibit characteristics which differ significantly from pure aluminas. One of the key properties of silica-aluminas is their comparatively high level of surface acidity, making them useful catalyst support materials, for example in the field of refinery catalyst.

Zyme-Flow® UN-657 is the core product in our chemical portfolio and has become the leader in process unit decontamination. In a single step application, Zyme-Flow UN657 removes residual oil, gas, benzene, LEL's, H2S, and pyrophoric iron sulfide. It is fast, safe and have effective decontamination. Zyme-Flow® UN-657 is safe, biodegradable, compatible with all metallurgy, and is wastewater friendly. There are no VOC's, no hazardous materials, and is rated [0-0-0] for health, flammability, and reactivity.

Zeolyst is a leading global supplier of specialty zeolite powders and catalysts.

Endcor® Corrosion resistant coatings include silicone alkyd, thermo setting epoxy,inorganic zincs, acrylic urethane, water borne silicone, coal tar epoxy, elastomeric, cold galvanizing compound.

Technobasalt Invest is a reliable supplier of high-quality basalt reinforcing materials Technobasalt Invest is one of the world’s largest players in the market of basalt materials made of continuous basalt yarn. The whole range of manufactured products is of excellent quality, confirmed by the relevant certificates and a number of tests. The company uses a management system in accordance with the ISO 9001: 2015 standard.

Fibertec mineral wool fibers are inorganic synthetic fibers that have been specifically milled and processed to controlled lengths and with predictable diameters and aspect ratios. These mineral fibers are generated from complex mineral silicates having as primary components silicates of calcium, magnesium and aluminum. Fibertec mineral fibers can be surface treated to enhance performance in selected resin systems. urther, because these fibers are additionally characterized by very low loose and tapped bulk densities, they are desirable for low-density reinforced thermoset and thermoplastic systems.

Ertalyte® PET grades have the following features: Good for both wet and dry environments High strength and rigidity - ideal for close tolerance parts Excellent stain resistance Good wear resistance and excellent dimensional stability Better resistance to acids than nylon or acetal

MARLOWET ether carboxylic acids are low foaming anionic surfactants. They are based on alcohols from C9 to C18, with different alkoxylation degrees. The MARLOWET product range is a water soluble lubricant efficient in hard water and active at extreme pH. It can be used in various applications including as a corrosion inhibitor (organic anti-corrosion agent), wetting agent, defoamer, hydrophilic emulsifier for water based metalworking fluids and exhibits high lime soap dispersing properties.

Our glass fiber reinforcements are 10 or 16 microns in diameter and milled to lengths ranging from 120 to 470 microns. They are used in composites to increase mechanical properties such as tensile, flexural and impact strength. They are also used to increase dimensional stability and minimize distortion at elevated temperatures. Milled glass fibers are compatible with all thermoset and thermoplastics resins. Surface treatments are available that may enhance performance. Microglass milled fibers are E-glass filaments hammer milled to various bulk densities. Microglass is used as a filler/reinforcement in composites to increase mechanical properties (tensile, flexural and impact), improve dimensional stability and minimize distortion at elevated temperatures.

COBALT™ is a liquid-to-liquid contact product to catalyze mercaptan (RSH) oxidation into disulfide oils (DSO).

Schultz combines the power of science and technology for innovation to extract value from the interaction of functional chemicals. With the extension of its product chain using renewable material structures, the trend of the Schultz high-value products to substitute similar products is recognized by end users worldwide. Our goal is to help reduce the processing cost and increase the advantage for our customers.

Fibertec micas are platy minerals. Mica is generically a complex group of aluminosilicates occurring naturally as plates or sheet-like forms. Fibertec micas can be surface treated to enhance performance in various resin systems. Fibertec mica is used as functional fillers providing reinforcement in thermoplastic and thermoset resins to improve flexural modulus, tensile strength, impact strength while minimizing shrinking and warping at elevated temperatures.