Products

BD54190 is a two-part, mineral filled, room temperature cure, epoxy adhesive designed for the bonding of metals, ceramics, and many plastics. It cures at room temperature to a tough, semi-flexible material. It has good wetting to most surfaces and is free flowing to penetrate cavities and give good self-leveling and air release. Because it is a filled epoxy, it gives very good vibration and impact resistance. It gives good resistance to water, salt spray, inorganic acids and bases and most organic solvents. It was especially formulated to a 1 part a to 1 part b volume ratio mix for use in side by side cartridges and meter mix equipment. BD54190 can reach handling cure at room temperature within 16 to 20 hours, but it can be accelerated by the use of heat. Times and temperatures from 2 hours at 65°c to 20 minutes at 100°c are typical for many applications. The time to heat the substrate must also be taken into consideration. Cooler temperatures will also extend work time and cure time.

BD5405 NS is a two-part, non-sag, room temperature cure, epoxy adhesive designed for high speed bonding of metals, ceramics, and most plastics. It is a thixotropic paste consistency to prevent running and sagging it gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 20 – 30 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD5430 is a two-part, unfilled room temperature cure, epoxy adhesive designed for bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 240 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD5425 is a two-part, unfilled room temperature cure, epoxy adhesive designed for bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 60 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD5405 flex is a two-part, unfilled rubber modified, room temperature cure, epoxy adhesive designed for high speed bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 20 – 30 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD5420 is a two-part, epoxy hybrid room temperature cure adhesive designed for bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 2:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 120 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD54125 is a two-part, unfilled, room temperature cure, epoxy adhesive designed for bonding metals and plastics. The product gives very good vibration and impact resistance with high peel and shear strength. It has a low viscosity for good substrate penetration and adhesion. It gives excellent resistance to water, salt spray, inorganic acids and bases and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment.

BD5460 is a two-part, epoxy hybrid room temperature cure adhesive designed industrial bonding, small potting and laminating where excellent strength and toughness, structural bonding, and mechanical and electrical properties are required. This 2-part adhesive cures at room temperature, exhibits good wetting, and develops high strength, low shrink bonds to most materials including fiberglass, ceramics, metals and many plastics. It has great dimensional stability over a wide range of temperatures. Fully cured bd5420 is a durable electrical insulator with resistance to water, weather, ozone and oxygen, various solvents, fuels, oils, alcohols, mild acids and alkalis and many other organic compounds including diesel fuel and gasoline. It is especially formulated for a 2:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 120 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD54110 is a two-part, unfilled, room temperature cure, epoxy adhesive designed for the bonding of metals, ceramics, and many plastics. This product gives exceptional resistance to water, salt spray, inorganic acids and bases and most organic solvents. This product gives better water and temperature resistance than just about any standard 5 minute epoxy product on the market place. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is typically achieved at room temperature with 30 to 60 minutes with full cure in 24 hours. An elevated temperature cure schedule can be used to reach final properties quickly.

BD5410 is a two-part, unfilled room temperature cure, epoxy adhesive designed for high speed bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 1:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 60 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.

BD54420 is a two-part, epoxy hybrid room temperature cure adhesive designed for bonding of metals, ceramics, and most plastics. It cures to a tough semi-rigid material, and is free flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It is especially formulated for a 2:1 mix ratio for use in side by side cartridges, or to be used by hand mixing, or use with meter mix equipment. A handling cure is normally achieved at room temperature within 360 minutes with a full cure at room temperature within 24 hours. To accelerate the final cure, or to quicken the handling simply elevate the temperature.