Products

CENTROCAR CENTROCARB GF / PC GF 30 is reinforced with 30% short-glass-fibers. This leads to stiffness of the composite material and an increased heat distortion resistance at the same time. The effect of tension tears is reduced. The maximum short-term highest applicable temperature is increased to 140 °C. Due to the outstanding electrical properties, PC GF 30-plastics are often used as insulation parts in the electronics industry.

CENTROMID 12 GF / PA 12 GF 30 is reinforced with 30% glassfibres. This leads to stiffness and increased resistance in the binding substance and an increased heat distortion resistance at the same time. The impact strength is reduced, the tensile strength is increased up to 6.000 MPa. PA 12 GF 30-plastics are often used as lever or valve components.

CENTROLEN / PP LF is added to the basic polypropylene polymer. The plastic can conduct electricity; the high resistance to tear and chemicals remains intact. The specific surface resistance is reduced to 10³ Ohm. PP LF-plastics are often used as filter heads, casings or as mechanical conveyors for flammable liquids.

CENTROLEN / PE-UHMW is polymerised with a modified Ziegler-Catalyst. The density is lowered and the sliding friction coefficient is improved. PE-UHMW distinguishes itself through its very high impact resistance and abrasion resistance. The BfR-/FDA approval assures physiological safety. Sliding guides or pump and wear parts are often manufactured from PE-UHMW.

CENTROMID 6.6 GF / PA 6.6 GF 30 is reinforced with 30% glass-fibers. This leads to stiffness and increased resistance in the binding substance and an increased heat distortion resistance at the same time. The impact strength is reduced, the tensile strength is increased up to 5.900 MPa. PA 6.6 GF 30-plastics are often used as housings or as spacer units.

CENTROLEN / PP-H is a semi-crystalline thermoplastic, but possesses higher resistance, stiffness and melting temperature with low density. The dynamic stability is equally high. PP-H is applicable within a temperature range of +2 to 130 °C. PP-H is used in apparatus engineering and in the chemical industry. The BfR-/FDA approval assures physiological safety. PP-H is available in the colors natural and gray.

CENTROTRON GF 15 / PPS GF 15 is reinforced with 15% glass-fibers. This leads to stiffness and increased resistance of the binding substance and an increased heat distortion resistance at the same time. The tensile strength is increased to 5.000 MPa. Among other things, bearings, sensors or exhaust pipes are manufactured from PPS GF 15 plastics.

CENTROMID 6 GF / PA 6 GF 30 is reinforced with 30% glass-fibers. This leads to stiffness and increased resistance in the composite material and an increased heat distortion resistance at the same time. The impact strength is reduced, the tensile strength is increased up to 8.700 MPa. PA 6 GF 30 plastics are often used as track and rope pulleys.

CENTROMID 12 / PA 12 is a high crystalline thermoplastic, which is comprised of one basic unit. The number 12 indicates the number of C-atoms of the basic molecular structure. PA 12 possesses high impact strength and only absorbs little moisture. The chemical resistance is improved. PA 12 is applicable to up to 150 °C. PA 12-plastics are often used as prec ision or drive components. The BfR-/FDA approval assures physiological safety. PA 12 is available in the colors natural and black.

CENTROTRON GF 40 / PPS GF 40 is strengthened with 40% glass-fibers. The result is additional stiffness and higher strength of the binding material and an increase of heat resistance stability at the same time. The bending strength increases to 14.000 MPa. PPS GF 40-plastics are often used in the automotive branch or in aircraft construction.

CENTROMID 6 E / PA 6 E is a high crystalline thermoplastic, which is comprised of one basic unit. The number 6 indicates the number of C-atoms of the basic molecular structure. PA 6 E possesses high toughness and heat stability. A high elastic-module is reached through hydrogen binding. PA 6 E is applicable within a temperature range of -40 to +160 °C. PA 6 E-parts are often used as bearings, gear wheels, rollers or seals. The BfR-/FDA approval assures physiological safety. PA 6 E is available in the colors natural and black.

CENTROMID 6 E FG / PA 6 E FG is a high crystalline thermoplastic, which is comprised of one basic unit. The number 6 indicates the number of C-atoms of the basic molecular structure. PA 6 E FG possesses high toughness and heat stability. A high elastic-module is reached through hydrogen binding. PA 6 E FG is applicable within a temperature range of -40 to +160 °C. PA 6 E FG-parts are often used as bearings, gear wheels, rollers or seals. The EU-VO 10/2011-/FDA approval assures physiological safety. PA 6 E FG is available in the color natural.

CENTROLEN / PP GF 30 is reinforced with 30% glass-fibers. This leads to stiffness and increased resistance in the binding substance and an increased heat distortion resistance at the same time. The impact strength is reduced, the tensile and bending strength is increased up to 6.500 MPa and/or 5.500 MPa. PP GF 30-plastics are often used as fan blades or air filter housings.

CENTROMID 6.6 / PA 6.6 is a high crystalline thermoplastic, which is comprised of two basic units. The number 6.6 indicates the number of C-atoms of both basic structures of the molecules. PA 6.6 possesses an increased resistance to toughness and wear, as well as an increased resistance to abrasion. Excellent toughness is given even in low temperatures. PA 6.6 is applicable within a temperature range of -30 to +180 °C. PA 6.6 plastics are often used as track rollers, rope pulleys or gear racks. The BfR-/FDA approval assures physiological safety. PA 6.6 is available in the colors natural and black.