Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Repels stains, oil and food products
- Excellent resistance to water intrusion
- Graffiti resistance
- Exhibits good beading effects
- No change in surface appearance
- Breathable system
- Deep penetration into the substrate
- High resistance to alkali attack
- Product Benefits
STAINGUARD-50 is designed to work without changing the natural appearance of the surface and is able to repel stains, oil and food products. STAINGUARD-WB is suitable for indoor and outdoor use and is able to seal hairline cracks up to 0.3 mm – does not flake or peel.
Chemical Products' state-of-the-art protective treatments have developed a reputation by architects and building professionals as the premier solution for water repellents and sealers. Chemical Products' is dedicated to solving the destructive influence water intrusion and other elements have on building materials.
Applications & Uses
- Applications
- Application Area
- Applications
- Building facades
- Floors
- Walls
- Swimming pool surrounds
- Patios
- Garages
- Kitchens
- Entertaining areas
- Limitations
- Not intended for below-grade waterproofing. Should not be applied if the surface temperature is below 20° F or above 100° F, if rain is expected within six hours following application, or if high winds or other conditions prevent proper application. If rain has preceded the application, the surface should be allowed to dry at least 24 hours. Caution should be taken with windows, motor vehicles, vegetation and adjacent surfaces. Check compatibility before application.
Properties
- Color
- Physical Form
- Appearance
- Clear yellow liquid
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Active Content | 100 | % | — |
| Active Solid Content | 10 | % | — |
| Value | Units | Test Method / Conditions | |
| Density | 0.95 | g/cm3 | — |
| VOC | max. 50 | g/l | — |
Technical Details & Test Data
- Installation
- All surfaces must be cleaned to remove all traces of dirt, dust, efflorescence, mold, salt, grease, oil, asphalt, laitance, curing compounds, paint, coatings and other contaminants. Acceptable surface cleaning methods include shot-blasting, sand-blasting, water-blasting and chemical cleaners. Check with your Chemical Products Industries, Inc. representative to verify suitable cleaning methods, products and that the surface preparation adequate. Before applying, it is recommended that preliminary tests be carried out to determine usage and to test the effectiveness of the treatment. Depending on the porosity of each designated surface, coverage rates can vary. Typical coverage is approximately 80-300 square feet per gallon. STAINGUARD-WB should be applied by low-pressure (15 to 25 psi) pumping equipment with a wet fan type spray nozzle. Alternate methods include nap roller (1”) or by brush. Horizontal surfaces should be treated until material puddles or stands on the surface. After ten minutes sweep, squeegee, or mop any remaining material to dry areas.Vertical surfaces should be treated using a wet-on-wet technique by applying from the bottom up with six to eight inch run down from the bottom of the spray pattern. During application, precautions should be taken to protect the surrounding area from overspray and run off. STAINGUARD-WB will not etch glass but will leave a residue on non-porous surfaces. Allow 24 hours for the product to cure before subjecting to traffic, moisture or oil.
Packaging & Availability
- Regional Availability
- Packaging and Distribution
- STAINGUARD-WB is available in 5 and 55 gallon containers to approved applicators and distributors throughout the United States. Contact Chemical Products Industries, Inc. at 800-624-4356 or 405-745-2070 for a sales representative in your area
Storage & Handling
- Precautions
- STAINGUARD-WB should be kept closed when not in use and should be stored at temperatures between 35° F and 120° F. Care should be taken to prevent moisture condensation in the container. Please refer to the Material Safety Data Sheet for more detailed information.