Products

Co-solvent soluble polyamide resin 100% Solids

Filtrez™ 530 A is an alcohol soluble fumaric acid modified rosin ester with a high softening point and high acid value. Filtrez 530 A has good solubility and low viscosity in alcohol and aqueous ammonia solutions, which contributes to high gloss in overprint varnishes. This resin is commonly used in solvent and water-based gravure and flexographic inks. Filtrez 530 A also be used as a leveling and gloss-promoting agent in floor polishes.

Alcohol soluble non film forming polyamide resin 100% Solids.

Co-solvent soluble polyamide resin 100% Solids

Terlon™ 613 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 613 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 613 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 613 A offers a very effective cost/quality ratio.

Hydro-Rez™ 5614 A is a fumarated rosin ester that is soluble in alcohol and can be dispersed in water using ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties, and is compatible with shellac and Manila copal resins. Hydro-Rez 5614 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Hydro-Rez™ 5626 A is a fumarated rosin ester that is soluble in alcohol, and can be dispersed in water with ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties and is compatible with shellac and Manila copal resins. Hydro-Rez 5626 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Terlon™ 607 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 607 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 607 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and color development during oxidation are markedly reduced. Terlon 607 A offers a very effective cost/quality ratio.

Pineclear 4305 is used in Lacquer coatings, Specialty coatings and Thermoplastic applications. Very low color, requires less liquid plasticizer in finished applications.

Optirub™ OP A is a micronized, oxidized polyethylene that easily disperses into aqueous systems. Optirub OP A is processed to a 12 micron average particle size and formulated to give excellent rub resistance, lubricity, gloss and anti-blocking properties. Addition levels range from 0.5 to 2%, depending upon application requirements.

Setaprint™ 2243 A is a moderately soluble, high viscosity free resin which exhibits excellent solvent release for fast setting and good holdout. Setaprint 2243 A has excellent compatibility with drying oils and it gives varnishes a hard, scuff resistant surface.

TerlonTM 605 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 605 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 605 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 605 A offers a very effective cost/quality ratio.

Pineclear 4307 is used in Lacquer coatings, Specialty coatings, and Thermoplastic applications. Very low color, high viscosity and melt point for demanding thermoplastic applications.

Ultrapoly™ 210 A is a high performance blend of tough, low COF polyethylene dispersed in a harddrying binder. Ultrapoly 210 A is recommended where abrasion, mar resistance, and slip are required. Ultrapoly 210 A is 100% non-volatile and fast-setting. It protects the film in the earliest stages of the printing process while developing exceptional toughness over time.

Flex-Rez™ 2433AD A is Lawter™ polyamide resin. Flex-Rez 2433AD A has served as the industry standard for surface printing applications on films or paper. Flex-Rez 2433AD A has excellent wet-pack resistance, coupled with excellent adhesion on difficult substrates such as polyethylene, polypropylene, and coated foils.

Ultrafine™ 1000 A is a finely micronized polyethylene wax powder recommended when maximum rub and mar resistance, block resistance, slip, re-coatability and elevated processing temperatures are required. The average particle size of Ultrafine 1000 A is 7 microns with a narrow distribution of particle sizes for ease of dispersion and uniformity during processing. Addition levels range from 0.5 to 3%, depending upon application requirements.

Optirub™ PC A is a finely micronized, polyethylene and carnauba blend processed to an 8 micron average particle size. Optirub PC A is recommended for applications where gloss retention, clarity, or inter-coat adhesion is important. In addition, Optirub PC A provides an excellent combination of slip, wet scuff, mar and block resistance. Optirub PC A is not recommended for recoating, imprinting, gluing, and die-stamping applications. Recommended usage level is 1 to 3%.

Ultrafine™ 1WLS A is a premium polytetrafluoroethylene fine powder used to improve surface properties of printing inks and coatings. Ultrafine 1WLS A is designed for lubricity, abrasion and heat resistance and may be used in combination with other waxes for the most effective balance of cost and performance. Ultrafine 1WLS A is characterized by a slightly broader particle size distribution. Recommended usage level is 1 to 4%.

Ultrapoly™ 213 A is a fine particle size blend polyethylene/PTFE dispersed in a 100% non-volatile, hard-drying binder. Ultrapoly 213 A is recommended for both sheetfed and heatset inks where gloss retention, lubricity, abrasion and mar resistance are required. Ultrapoly 213 A is coatable and may be used for laser work. For optimum heat resistance, we recommend using 3 parts Ultrapoly 213 A to 1 part Fluoron™ 960 A (a 50% PTFE concentrate). Recommended usage level is 3 to 5%.

Polysperse™ A is a linear hydrocarbon produced by the Fischer-Tropsch process. Polysperse A has a unique spherical morphology and narrow distribution of particles for ease of dispersion and uniformity during processing. Polysperse A exhibits low surface tension, exceptional surface slip and smoothness, rub resistance, gloss, and non-marking properties. Addition levels range from 0.5-3%, depending upon application requirements.

Optirub™ SP1 A is a finely, micronized blend of tough polyethylene wax and premium grade PTFE. Optirub SP1 A is processed to a 6 micron average particle size and formulated to give a high degree of surface lubricity and rub resistance in inks and coatings. Addition levels range from 0.5 to 3%, depending upon application requirements.

Ultrapoly™ 211 A is a PTFE modified version of Ultrapoly 210 A. Ultrapoly 211 A is a high performance blend of tough, low COF polyethylene/PTFE dispersed in a hard drying binder. Ultrapoly 211 A is recommended where a high degree of slip, heat resistance, and abrasion resistance are required. Ultrapoly 211 A is 100% non-volatile and fast-setting. It protects the film in the earliest stages of the printing process while developing exceptional toughness over time. Ultrapoly 211 A is coatable and may be used for laser work. For optimum heat resistance, we recommend using 3 parts Ultrapoly 211 A to 1 part Fluoron™ 735 A (a 50% PTFE concentrate). Recommended usage level is 3 to 5%.

Setaprint™ 150 A is a Lawter™ phenolic modified rosin ester. Setaprint 150 A is a unique ultra-high molecular weight resin, possessing high viscosity while maintaining a workable dilution range. Setaprint 150 A provides greater compatibility with drying oils and alkyds then ever achieved before at this viscosity. These combined properties allow Setaprint 150A to help improve gloss, transfer, dot sharpness, gel structure and press stability. This resin provides an inner structure in solution allowing for reduction in gelling agents and improved stability of gelled systems

Alcohol soluble polyamide resin 100% Solids.

Alcohol soluble polyamide resin 100% Solids.

Ultrafine™ 1W A is a polytetrafluoroethylene fine powder used to improve surface properties of printing inks and coatings. Ultrafine 1W A is designed for lubricity, abrasion and heat resistance and may be used in combination with other waxes for the most effective balance of cost and performance. Recommended usage level is 1 to 4%.

Ultrapoly™ 2300 A is a softer bodied, pumpable version of Ultrapoly 210 A. Ultrapoly 2300 A is a high performance blend of tough, low COF polyethylene dispersed in a hard-drying binder. Ultrapoly 2300 A is recommended where abrasion and mar resistance, slip, and pumpability are required. Ultrapoly 2300 A is a 100% non-volatile and fast-setting, protecting the film in the earliest stages of the printing process, while developing exceptional toughness over time. Ultrapoly 2300 A is coatable and may also be used for laser work, when combined with PTFE. For optimum heat resistance, we recommend using 3 parts Ultrapoly 2300 A to 1 part Fluoron™ 735 A (a 50% PTFE concentrate). Recommended usage level is 4 to 6%.

Flex-rez 1255 AS combines excellent alcohol solubility with nitrocellulose compatibility to produce flexographic inks having excellent gloss and runnability. It exhibits excellent tolerance for ester solvents. The high degree of compatibility along with high solubility makes Flex-rez 1255 AS an excellent polyamide for pigment wetting applications. Additionally, Flex-rez 1255 AS has outstanding gel resistance and can be used to improve gel characteristics when combined with traditional polyamide resins. Flex-rez 1255 AS has excellent adhesion on all difficult substrates.