Products

Pineclear 4306 is used in Specialty coatings and Thermoplastic applications. Very low color, stabilized rosin for enhanced heat stability. It provides excellent adhesion and high bio-renewable content.

Filtrez™ 531 A is an alcohol soluble fumaric acid modified rosin ester with a high softening point and moderately high acid value. Filtrez™ 531 A can be used in solvent and water-based flexographic and in gravure inks. This resin can also be used as a leveling and gloss-promoting agent in floor polishes.

Co-solvent soluble polyamide resin 100% Solids

Optilith™ AM A is an anti-mist compound. Optilith AM A is a 95% non-volatile, high solids paste. Optilith AM A gives maximum reduction in misting without adversely effecting gloss or ink rheology. Optilith AM A is effective at 0.5 to 3% use levels.

Bodied workhorse.

Filtrez™ 530 A is an alcohol soluble fumaric acid modified rosin ester with a high softening point and high acid value. Filtrez 530 A has good solubility and low viscosity in alcohol and aqueous ammonia solutions, which contributes to high gloss in overprint varnishes. This resin is commonly used in solvent and water-based gravure and flexographic inks. Filtrez 530 A also be used as a leveling and gloss-promoting agent in floor polishes.

Alcohol soluble non film forming polyamide resin 100% Solids.

Filtrez™ 3320 A is a maleic modified rosin ester made for ink and nitrocellulose lacquer systems that have low aromatic solvents. Filtrez™ 3320 A is considered suitable for use in gravure and flexographic inks and coatings.

Co-solvent soluble polyamide resin 100% Solids

Terlon™ 613 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 613 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 613 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 613 A offers a very effective cost/quality ratio.

Bodied workhorse.

Hydro-Rez™ 5614 A is a fumarated rosin ester that is soluble in alcohol and can be dispersed in water using ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties, and is compatible with shellac and Manila copal resins. Hydro-Rez 5614 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Alcohol soluble polyamide resin 100% Solids.

Ultrafine™ 1W A is a polytetrafluoroethylene fine powder used to improve surface properties of printing inks and coatings. Ultrafine 1W A is designed for lubricity, abrasion and heat resistance and may be used in combination with other waxes for the most effective balance of cost and performance. Recommended usage level is 1 to 4%.

Pineclear 4305 is used in Lacquer coatings, Specialty coatings and Thermoplastic applications. Very low color, requires less liquid plasticizer in finished applications.

Hydro-Rez™ 5626 A is a fumarated rosin ester that is soluble in alcohol, and can be dispersed in water with ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties and is compatible with shellac and Manila copal resins. Hydro-Rez 5626 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Pinerez® 2307 is a stablized rosin for excellent color stability, excellent adhesion and high bio-renewable content. It's used in Specialty coatings and Thermoplastic applications.

Terlon™ 607 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 607 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 607 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and color development during oxidation are markedly reduced. Terlon 607 A offers a very effective cost/quality ratio.

Pineclear 4307 is used in Lacquer coatings, Specialty coatings, and Thermoplastic applications. Very low color, high viscosity and melt point for demanding thermoplastic applications.

Filtrez™ 3310 A is a maleic modified rosin ester. Filtrez 3310 A is designed for the thermoplastic pavement marking industry, and it allows for less plasticizer in the finished application. Other possible applications include modifying nitrocellulose for lacquer in the coatings industry.

TerlonTM 605 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 605 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 605 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 605 A offers a very effective cost/quality ratio.

Setaprint™ 2243 A is a moderately soluble, high viscosity free resin which exhibits excellent solvent release for fast setting and good holdout. Setaprint 2243 A has excellent compatibility with drying oils and it gives varnishes a hard, scuff resistant surface.

Optirub™ OP A is a micronized, oxidized polyethylene that easily disperses into aqueous systems. Optirub OP A is processed to a 12 micron average particle size and formulated to give excellent rub resistance, lubricity, gloss and anti-blocking properties. Addition levels range from 0.5 to 2%, depending upon application requirements.

Pinerez® 2308 is a Stablized rosin for excellent color and heat stability. Excellent adhesion to a variety of substrates. It's used in Specialty coatings and Thermoplastic applications.

Terlon™ 1143 A alkyd is known for its excellent pigment wetting ability and fast hard-drying properties. This alkyd is an essential ingredient in many oil-based printing inks. Terlon 1143 A aids in development and maintenance of color strength with minimal bronzing and provides flow and leveling where required. Terlon 1143 A is an important formulating tool. Terlon 1143 A is also very compatible with most ink vehicles and serves to stabilize ink formulations. Metal decorating inks based on this alkyd bake very fast and form hard abrasion resistant, glossy surfaces

Ultrapoly™ 210 A is a high performance blend of tough, low COF polyethylene dispersed in a harddrying binder. Ultrapoly 210 A is recommended where abrasion, mar resistance, and slip are required. Ultrapoly 210 A is 100% non-volatile and fast-setting. It protects the film in the earliest stages of the printing process while developing exceptional toughness over time.

Polysperse™ A is a linear hydrocarbon produced by the Fischer-Tropsch process. Polysperse A has a unique spherical morphology and narrow distribution of particles for ease of dispersion and uniformity during processing. Polysperse A exhibits low surface tension, exceptional surface slip and smoothness, rub resistance, gloss, and non-marking properties. Addition levels range from 0.5-3%, depending upon application requirements.

Setaprint™ 150 A is a Lawter™ phenolic modified rosin ester. Setaprint 150 A is a unique ultra-high molecular weight resin, possessing high viscosity while maintaining a workable dilution range. Setaprint 150 A provides greater compatibility with drying oils and alkyds then ever achieved before at this viscosity. These combined properties allow Setaprint 150A to help improve gloss, transfer, dot sharpness, gel structure and press stability. This resin provides an inner structure in solution allowing for reduction in gelling agents and improved stability of gelled systems

Pineclear 4307 is used in Specialty coatings and Thermoplastic applications. Very low color, stabilized rosin for enhanced heat stability. It provides excellent adhesion and high bio-renewable content.

Ultrapoly™ 211 A is a PTFE modified version of Ultrapoly 210 A. Ultrapoly 211 A is a high performance blend of tough, low COF polyethylene/PTFE dispersed in a hard drying binder. Ultrapoly 211 A is recommended where a high degree of slip, heat resistance, and abrasion resistance are required. Ultrapoly 211 A is 100% non-volatile and fast-setting. It protects the film in the earliest stages of the printing process while developing exceptional toughness over time. Ultrapoly 211 A is coatable and may be used for laser work. For optimum heat resistance, we recommend using 3 parts Ultrapoly 211 A to 1 part Fluoron™ 735 A (a 50% PTFE concentrate). Recommended usage level is 3 to 5%.

Alcohol soluble polyamide resin 100% Solids.

Flex-Rez™ 2433AD A is Lawter™ polyamide resin. Flex-Rez 2433AD A has served as the industry standard for surface printing applications on films or paper. Flex-Rez 2433AD A has excellent wet-pack resistance, coupled with excellent adhesion on difficult substrates such as polyethylene, polypropylene, and coated foils.

Optirub™ SP1 A is a finely, micronized blend of tough polyethylene wax and premium grade PTFE. Optirub SP1 A is processed to a 6 micron average particle size and formulated to give a high degree of surface lubricity and rub resistance in inks and coatings. Addition levels range from 0.5 to 3%, depending upon application requirements.

Ultrapoly™ 213 A is a fine particle size blend polyethylene/PTFE dispersed in a 100% non-volatile, hard-drying binder. Ultrapoly 213 A is recommended for both sheetfed and heatset inks where gloss retention, lubricity, abrasion and mar resistance are required. Ultrapoly 213 A is coatable and may be used for laser work. For optimum heat resistance, we recommend using 3 parts Ultrapoly 213 A to 1 part Fluoron™ 960 A (a 50% PTFE concentrate). Recommended usage level is 3 to 5%.

Optirub™ PC A is a finely micronized, polyethylene and carnauba blend processed to an 8 micron average particle size. Optirub PC A is recommended for applications where gloss retention, clarity, or inter-coat adhesion is important. In addition, Optirub PC A provides an excellent combination of slip, wet scuff, mar and block resistance. Optirub PC A is not recommended for recoating, imprinting, gluing, and die-stamping applications. Recommended usage level is 1 to 3%.

Ultrafine™ 1000 A is a finely micronized polyethylene wax powder recommended when maximum rub and mar resistance, block resistance, slip, re-coatability and elevated processing temperatures are required. The average particle size of Ultrafine 1000 A is 7 microns with a narrow distribution of particle sizes for ease of dispersion and uniformity during processing. Addition levels range from 0.5 to 3%, depending upon application requirements.