Products

Co-solvent soluble polyamide resin 100% Solids

Filtrez™ 530 A is an alcohol soluble fumaric acid modified rosin ester with a high softening point and high acid value. Filtrez 530 A has good solubility and low viscosity in alcohol and aqueous ammonia solutions, which contributes to high gloss in overprint varnishes. This resin is commonly used in solvent and water-based gravure and flexographic inks. Filtrez 530 A also be used as a leveling and gloss-promoting agent in floor polishes.

Alcohol soluble non film forming polyamide resin 100% Solids.

Co-solvent soluble polyamide resin 100% Solids

Terlon™ 613 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 613 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 613 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 613 A offers a very effective cost/quality ratio.

Hydro-Rez™ 5614 A is a fumarated rosin ester that is soluble in alcohol and can be dispersed in water using ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties, and is compatible with shellac and Manila copal resins. Hydro-Rez 5614 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Alcohol soluble polyamide resin 100% Solids.

Ultrafine™ 1W A is a polytetrafluoroethylene fine powder used to improve surface properties of printing inks and coatings. Ultrafine 1W A is designed for lubricity, abrasion and heat resistance and may be used in combination with other waxes for the most effective balance of cost and performance. Recommended usage level is 1 to 4%.

Pineclear 4305 is used in Lacquer coatings, Specialty coatings and Thermoplastic applications. Very low color, requires less liquid plasticizer in finished applications.

Hydro-Rez™ 5626 A is a fumarated rosin ester that is soluble in alcohol, and can be dispersed in water with ammonia or morpholine. The high melting point promotes fast solvent release and good leveling properties and is compatible with shellac and Manila copal resins. Hydro-Rez 5626 A is recommended for use in solvent or water-based flexographic inks. This resin is also recommended for use in mineral spirit varnishes.

Terlon™ 607 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 607 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 607 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and color development during oxidation are markedly reduced. Terlon 607 A offers a very effective cost/quality ratio.

Pineclear 4307 is used in Lacquer coatings, Specialty coatings, and Thermoplastic applications. Very low color, high viscosity and melt point for demanding thermoplastic applications.

TerlonTM 605 A is a soybean oil alkyd. It can carry and print a higher load of pigment than bodied oils and conventional alkyds. Terlon 605 A shows good color retention characteristics and hence is recommended for use in heat induced drying applications. Terlon 605 A dries by oxidation and forms a flexible film. While drying times are slower than pure linseed oil based alkyds, initial odor and odor development during oxidation are markedly reduced. Terlon 605 A offers a very effective cost/quality ratio.

Setaprint™ 2243 A is a moderately soluble, high viscosity free resin which exhibits excellent solvent release for fast setting and good holdout. Setaprint 2243 A has excellent compatibility with drying oils and it gives varnishes a hard, scuff resistant surface.

Optirub™ OP A is a micronized, oxidized polyethylene that easily disperses into aqueous systems. Optirub OP A is processed to a 12 micron average particle size and formulated to give excellent rub resistance, lubricity, gloss and anti-blocking properties. Addition levels range from 0.5 to 2%, depending upon application requirements.

Polysperse™ A is a linear hydrocarbon produced by the Fischer-Tropsch process. Polysperse A has a unique spherical morphology and narrow distribution of particles for ease of dispersion and uniformity during processing. Polysperse A exhibits low surface tension, exceptional surface slip and smoothness, rub resistance, gloss, and non-marking properties. Addition levels range from 0.5-3%, depending upon application requirements.

Setaprint™ 150 A is a Lawter™ phenolic modified rosin ester. Setaprint 150 A is a unique ultra-high molecular weight resin, possessing high viscosity while maintaining a workable dilution range. Setaprint 150 A provides greater compatibility with drying oils and alkyds then ever achieved before at this viscosity. These combined properties allow Setaprint 150A to help improve gloss, transfer, dot sharpness, gel structure and press stability. This resin provides an inner structure in solution allowing for reduction in gelling agents and improved stability of gelled systems

Alcohol soluble polyamide resin 100% Solids.

Flex-Rez™ 2433AD A is Lawter™ polyamide resin. Flex-Rez 2433AD A has served as the industry standard for surface printing applications on films or paper. Flex-Rez 2433AD A has excellent wet-pack resistance, coupled with excellent adhesion on difficult substrates such as polyethylene, polypropylene, and coated foils.

Optirub™ SP1 A is a finely, micronized blend of tough polyethylene wax and premium grade PTFE. Optirub SP1 A is processed to a 6 micron average particle size and formulated to give a high degree of surface lubricity and rub resistance in inks and coatings. Addition levels range from 0.5 to 3%, depending upon application requirements.

Ultrafine™ 1000 A is a finely micronized polyethylene wax powder recommended when maximum rub and mar resistance, block resistance, slip, re-coatability and elevated processing temperatures are required. The average particle size of Ultrafine 1000 A is 7 microns with a narrow distribution of particle sizes for ease of dispersion and uniformity during processing. Addition levels range from 0.5 to 3%, depending upon application requirements.

Flex-rez 1255 AS combines excellent alcohol solubility with nitrocellulose compatibility to produce flexographic inks having excellent gloss and runnability. It exhibits excellent tolerance for ester solvents. The high degree of compatibility along with high solubility makes Flex-rez 1255 AS an excellent polyamide for pigment wetting applications. Additionally, Flex-rez 1255 AS has outstanding gel resistance and can be used to improve gel characteristics when combined with traditional polyamide resins. Flex-rez 1255 AS has excellent adhesion on all difficult substrates.

Ultrafine™ 1WLS A is a premium polytetrafluoroethylene fine powder used to improve surface properties of printing inks and coatings. Ultrafine 1WLS A is designed for lubricity, abrasion and heat resistance and may be used in combination with other waxes for the most effective balance of cost and performance. Ultrafine 1WLS A is characterized by a slightly broader particle size distribution. Recommended usage level is 1 to 4%.