Products

Semi-crystalline thermoplastic with high Hardness, rigidity and mechanical strength as well good creep resistance. By adding a it has a special, homogeneously distributed solid lubricant, compared to pure PET, improved sliding properties and higher abrasion resistance.

The properties are essentially the same as those of LiNNOTAM comparable. By adding molybdenum disulphite, a higher crystallinity is achieved in the material compared to pure cast polyamide.

Extruded polyamide 6 with good strength, impact resistance and good damping properties behave. Due to the manufacturing process, PA 6 has a higher moisture absorption. Compared to cast polyamide, however, it is less dimensionally stable & wear-resistant.

Semi-crystalline thermoplastic with high Hardness, rigidity and mechanical strength as well good creep resistance. PET has very good ones Sliding properties and shows little sliding wear. Also for parts due to its good dimensional stability good with high demands on dimensional accuracy suitable.

Amorphous high-performance plastic with high mechanical strength and rigidity as well as good Creep resistance over a wide temperature range. In addition, PSU has a high long-term use temperature, good dimensional stability and is Resistant to hydrolysis

LiNNOTAM with oil finely distributed in the material. LiNNOTAMGLiDE has the added Lubricant self-lubricating properties and has excellent wear resistance low coefficient of friction.

Partly crystalline thermoplastic material with high toughness and chemical resistance, but lower compared to other plastics mechanical strength. Because of its high molar mass of approx. 4,500,000 g / mol is very good Wear resistance and vibration damping.

LiNNOTAM with solid lubricants, additives and stabilizers finely distributed in the material. LiNNOTAMGLIDE Pro T has self-lubricating properties due to the added components and shows excellent wear resistance at very high low coefficient of friction.

In essence, the properties are similar to those of LiNNOTAM comparable. Through the use of special Additives is compared to pure cast polyamide however, a higher crystallinity is achieved in the material.

Semi-crystalline high-performance plastic with very good sliding properties and very good mechanical Properties even under thermal stress. In addition, PEEK is characterized by a excellent chemical resistance.

Semi-crystalline thermoplastic with high Rigidity and very good chemical resistance. PP-H exhibits compared to other plastics has a low density and is a very good one electrical insulator. For sliding applications is PP-H not suitable due to wear and tear.

On the basis of the activated anionic reaction LiNNOTAMHiPERFORMANCE 1200 Manufactured using the pressureless free-standing casting process. The process creates a high-molecular, highly crystalline and largely stressfree material with very good Wear resistance and dimensional stability

Polyamide produced on the basis of direct polymerisation in casting molds with a partially crystalline structure. The high proportion of crystallites leads to excellent mechanical properties such as very high abrasion and wear resistance, hardness and rigidity.

Compared to LiNNOTAM indicates LiNNOTAMDRiVE 600 Fe higher impact and shock resistance, higher elasticity and less tendency to absorb moisture. In addition, the material is characterized by a improved creep behavior.

This polyamide from caprolactam and laurolactam produced in the free-casting process shows in comparison to pure LiNNOTAM has a higher impact and shock resistance as well as a lower tendency to absorb moisture. In addition, the material is characterized by improved creep behavior and higher elasticity.

Semi-crystalline high-performance plastic with targeted improved sliding properties through the addition of solid lubricants. The excellent Properties of pure PEEK are enhanced by the Additives are not adversely affected and remain Receive.

Amorphous high-performance plastic with high mechanical strength and rigidity as well as good Creep resistance over a wide temperature range. In addition, PEI has a high long-term use temperature and good dimensional stability and is resistant to hydrolysis

Polyamide produced in the extrusion process with high hardness, rigidity and wear resistance but lower impact strength. The properties of PA66 are comparable to those of PA6 G. the However, the material absorbs and is more moisture less true to size.

Highly crystalline fluoroplastic with excellent Sliding properties, an anti-adhesive surface, best insulation properties and one almost universal chemical resistance. Disadvantageous is the low mechanical strength as well as that high specific weight.

Semi-crystalline thermoplastic with high Hardness, rigidity and mechanical strength as well good creep resistance. By adding a it has a special, homogeneously distributed solid lubricant, compared to pure PET, improved sliding properties and higher abrasion resistance.